OSG Point Taps（Tap Type：Point tap）
| Shipping Days |
|
|---|
?* Information on days to ship and prices
-
Point Tap Series, Tin Coated, TIN-POT
OSG
Though workpiece can be widely applied, it is suitable for high speed tapping of through holes, such as tempered material, and especially stainless steel- Volume Discount
Starting from∗ ： 15.45 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
- Promotional pricing ends 30/11/2024
Point Tap Series, for General, EX-POT
OSG
Suited for materials that leave coil shaped connected cutting dust that is in general use such as carbon steel, alloyed steel, and non-ferrous metals. Reliably Pushes Cutting Debris Forward Removing Concerns of Debris Interference- Volume Discount
Starting from∗ ： 7.45 € Special price Min. Shipping Days ： Same day *Unit price with basic configuration
-
A Tap Series for Pipes Point Tap A-POT
OSG
Has stable chip extraction and can be used for various work materials in a wide range of cutting areas and machines. Point taps with points grooves that are used in through holes.- Volume Discount
Starting from∗ ： 15.94 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
Point Tap Series, V Coated, V-POT
OSG
Compatible with a wide range of materials - soft materials to hard materials. Displays particularly good performance in tapping under high speed, highly dilution (water soluble cutting fluid) conditions. Also Effective For Dry-Tapping- Volume Discount
Starting from∗ ： 24.73 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
- Promotional pricing ends 30/11/2024
Point Tap Series For Stainless Steel Use EX-SUS-POT
OSG
Offers superb sharpness and durability. Can be used to drill holes in difficult-to-cut stainless steel.- Volume Discount
Starting from∗ ： 8.65 € Special price Min. Shipping Days ： Same day *Unit price with basic configuration
-
Point Tap Series, Ultra Synchronizing Taps, HS-RFT
OSG
Suited for through thread cutting using machinery equipped with complete lead feeding mechanisms.- Volume Discount
Starting from∗ ： 30.20 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
Starting from∗ ： 14.02 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
Point Tap Series, HR Coating, for NI-Base Heat Resistant Alloys, WHR-NI-POT
OSG
In applying HR coating with high welding-resisting properties on nickel based alloys, it achieves a long operating life even on aging nickel based alloys (40-45 HRC)Starting from∗ ： 28.34 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
Point Tap Series, TIN Coating, Long Shank, TIN-LT-POT
OSG
Though workpiece can be widely applied, it is suitable for high speed tapping of through holes, such as tempered material, and especially stainless steel- Volume Discount
Starting from∗ ： 22.83 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
Point Tap Series, V Coating, Long Shank, V-LT-POT
OSG
Compatible with a wide range of materials - soft materials to hard materials. Displays particularly good performance in tapping under high speed, highly dilution (water soluble cutting fluid) conditions. Also Effective For Dry-TappingStarting from∗ ： 23.17 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
- Promotional pricing ends 30/11/2024
Point Tap Series, Ultra Synchronizing Taps for Aluminum, HS-AL-RFT
OSG
Can conduct high speed / high precision thread cutting of aluminum and aluminum alloys when used exclusively with tools equipped with complete lead feeding machinery.- Volume Discount
Starting from∗ ： 11.81 € Special price Min. Shipping Days ： Same day *Unit price with basic configuration
-
Point Tap Series, Long Shank for Stainless Steel, EX-LT-SUS-POT
OSG
Shows the great sharpness and durability when used in through holes of machinability bad stainless steel- Volume Discount
Starting from∗ ： 14.35 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
Point Tap Series, General Homo Treatment, EX-H-POT
OSG
Used in cases such as insufficient protruding length of the threaded portion of the standard point-tap- Volume Discount
Starting from∗ ： 8.22 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
- Promotional pricing ends 30/11/2024
Point Tap Series, General Long Shank, EX-LT-POT
OSG
Used in cases such as insufficient protruding length of the threaded portion of the standard point-tap- Volume Discount
Starting from∗ ： 14.02 € Special price Min. Shipping Days ： Same day *Unit price with basic configuration
-
Point Tap Series, High Speed Synchronizing Taps, JIS Shank, J-HS-RFT
OSG
Suited for through thread cutting using machinery equipped with complete lead feeding mechanisms.- Volume Discount
Starting from∗ ： 21.73 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
Point Tap Series, High Speed Synchronizing Taps, Long Shank, HS-LT-RFT
OSG
Suited for through thread cutting using machinery equipped with complete lead feeding mechanisms.Starting from∗ ： 27.13 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
- Promotional pricing ends 30/11/2024
Point Tap Series, for Deep Holes, EX-DH-POT
OSG
Suitable for through holes with extra long threads and materials that easily suffer sticking.- Volume Discount
Starting from∗ ： 8.65 € Special price Min. Shipping Days ： Same day *Unit price with basic configuration
-
- Promotional pricing ends 30/11/2024
Point Tap Series, for Difficult-to-Machine Material, CPM-POT
OSG
Workpiece material is suitable for through hole drilling of about 20 ~ 45 HRC hardness of the tempered material or high-carbon steel, tool steel, alloy steel forging- Volume Discount
Starting from∗ ： 9.49 € Special price Min. Shipping Days ： Same day *Unit price with basic configuration
-
Point Tap Series, Long Shank for Difficult-To-Machine Material, CPM-LT-POT
OSG
Workpiece material is suitable for through hole drilling of about 20 ~ 45 HRC hardness of the tempered material or high-carbon steel, tool steel, alloy steel forging- Volume Discount
Starting from∗ ： 40.05 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
- Promotional pricing ends 30/11/2024
Point Tap Series, for Thin Plates, EX-SS-POT
OSG
Well suited for thread cutting of soft steel sheets with a pull strength of 700N or below. Achieves Beautiful Finishing Surfaces by Preventing Whiskers, Burrs, and Tears on Punched Holes and Buring Holes- Volume Discount
Starting from∗ ： 7.61 € Special price Min. Shipping Days ： Same day *Unit price with basic configuration
-
A Tap Series Point Tap Long Shank A-LT-POT
OSG
Has stable chip extraction and can be used for various work materials in a wide range of cutting areas and machines. Point taps with points grooves that are used in through holes.Starting from∗ ： 23.65 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
| Brand |
|---|
| Product Series |
| Starting from∗ |
| Min. Shipping Days ： |
| Screw Types |
| Screw size (Nominal) |
| Pitch (P), Number of Threading(mm) |
| Chamfer threads (Lcf) |
| Tool Material Type |
| work material |
| Tap Type |
| Hole type |
| Coating Y/N |
| Coating Type |
| Overall Length (L)(mm) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| Brand | OSG | OSG | OSG | OSG | OSG | OSG | OSG | OSG | OSG | OSG | OSG | OSG | OSG | OSG | OSG | OSG | OSG | OSG | OSG | OSG | OSG |
| Product Series | Point Tap Series, General Homo Treatment Long Shank, EX-LT-H-POT | Point Tap Series, HR Coating, for NI-Base Heat Resistant Alloys, WHR-NI-POT | Point Tap Series, Ultra Synchronizing Taps for Aluminum, HS-AL-RFT | Point Tap Series, Long Shank for Stainless Steel, EX-LT-SUS-POT | Point Tap Series, High Speed Synchronizing Taps, JIS Shank, J-HS-RFT | Point Tap Series, High Speed Synchronizing Taps, Long Shank, HS-LT-RFT | Point Tap Series, for Difficult-to-Machine Material, CPM-POT | Point Tap Series, Long Shank for Difficult-To-Machine Material, CPM-LT-POT | |||||||||||||
| Starting from∗ | 15.45 € *Unit price with basic configuration Volume Discount | 7.45 € Special price *Unit price with basic configuration Promotional pricing ends 30/11/2024Volume Discount | 15.94 € *Unit price with basic configuration Volume Discount | 24.73 € *Unit price with basic configuration Volume Discount | 8.65 € Special price *Unit price with basic configuration Promotional pricing ends 30/11/2024Volume Discount | 30.20 € *Unit price with basic configuration Volume Discount | 14.02 € *Unit price with basic configuration Volume Discount | 28.34 € *Unit price with basic configuration | 22.83 € *Unit price with basic configuration Volume Discount | 23.17 € *Unit price with basic configuration | 11.81 € Special price *Unit price with basic configuration Promotional pricing ends 30/11/2024Volume Discount | 14.35 € *Unit price with basic configuration Volume Discount | 8.22 € *Unit price with basic configuration Volume Discount | 14.02 € Special price *Unit price with basic configuration Promotional pricing ends 30/11/2024Volume Discount | 21.73 € *Unit price with basic configuration Volume Discount | 27.13 € *Unit price with basic configuration | 8.65 € Special price *Unit price with basic configuration Promotional pricing ends 30/11/2024Volume Discount | 9.49 € Special price *Unit price with basic configuration Promotional pricing ends 30/11/2024Volume Discount | 40.05 € *Unit price with basic configuration Volume Discount | 7.61 € Special price *Unit price with basic configuration Promotional pricing ends 30/11/2024Volume Discount | 23.65 € *Unit price with basic configuration |
| Min. Shipping Days ： | 6 Days | Same day | 6 Days | 6 Days | Same day | 6 Days | 6 Days | 6 Days | 6 Days | 6 Days | Same day | 6 Days | 6 Days | Same day | 6 Days | 6 Days | Same day | Same day | 6 Days | Same day | 6 Days |
| Screw Types | Meter | Meter / Unified / Whitworth / Sewing Machine | Meter / Unified | Meter | Meter / Unified / Whitworth | Meter | Meter | Meter | Meter | Meter | Meter | Meter | Meter | Meter | Meter | Meter | Meter | Meter | Meter | Meter | Meter |
| Screw size (Nominal) | M1.4 ～ M42 | No0UN ～ M48 | 1/2-20UNF ～ M24 | M8 ～ M10 | 1UN ～ M42 | M3 ～ M14 | M3 ～ M20 | M8 | M3 ～ M24 | M4 ～ M6 | M2 ～ M6 | M3 ～ M24 | M2 ～ M42 | M2 ～ M36 | M3 ～ M14 | M3 ～ M30 | M2 ～ M16 | M1.4 ～ M48 | M8 ～ M12 | M1.4 ～ M12 | M2 ～ M24 |
| Pitch (P), Number of Threading(mm) | 0.3 ～ 4.5 | 0.25 ～ 80 | 0.25 ～ 3 | 1 ～ 1.25 | 0.3 ～ 48 | 0.5 ～ 2 | 0.5 ～ 2.5 | 1.25 | 0.5 ～ 3 | 0.7 ～ 1 | 0.4 ～ 1 | 0.5 ～ 3 | 0.4 ～ 4.5 | 0.4 ～ 4 | 0.5 ～ 2 | 0.5 ～ 3.5 | 0.4 ～ 2 | 0.3 ～ 5 | 1.25 ～ 1.75 | 0.3 ～ 1.75 | 0.25 ～ 3 |
| Chamfer threads (Lcf) | 5P | 5P | 5P | 5P | 4P | 6P | 5P | 5P | 5P | 5P | 6P | 4P | 5P | 5P | 5P | 6P | 4P | 5P | 5P | 5P | 5P |
| Tool Material Type | Vanadium High-Speed Steel | Vanadium High-Speed Steel | Powder high-speed steel | Vanadium High-Speed Steel | Vanadium High-Speed Steel | Vanadium High-Speed Steel | Vanadium High-Speed Steel | Powder high-speed steel | Vanadium High-Speed Steel | Vanadium High-Speed Steel | Vanadium High-Speed Steel | Vanadium High-Speed Steel | Vanadium High-Speed Steel | Vanadium High-Speed Steel | Vanadium High-Speed Steel | Vanadium High-Speed Steel | Vanadium High-Speed Steel | Powder high-speed steel | Powder high-speed steel | Vanadium High-Speed Steel | Powder high-speed steel |
| work material | Low-Carbon Steel (carbon alloy less than 0.25%)[○] / Medium carbon steel (carbon content 0.25 to 0.45%)[○] / High Carbon Steel (C with a content over 0.45%)[○] / Alloy Steel (SCM)[○] / Stainless Steel (JIS-SUS)[◎] / Tool Steel (Before SKD Hardening)[○] / Steel casting (SC)[○] / Ductile Cast Iron (FCD)[○] / Copper (Cu)[○] / Brass (Bs)[○] / Brass cast iron (BsC)[○] / Bronze (Pb)[○] / Aluminum Rolled Material (AL)[○] / Aluminum Alloy Casting (AC, ADC)[○] / Magnesium Alloy (MC)[○] / Zinc Alloy Casting (ZDC)[○] / Titanium Alloy (Ti-6Al-4V, etc)[○] / Thermoplastic plastic (vinyl chloride, nylon, etc.)[○] | Medium carbon steel (carbon content 0.25 to 0.45%)[○] / High Carbon Steel (C with a content over 0.45%)[○] / Alloy Steel (SCM)[○] / Cast Iron (FC)[○] / Ductile Cast Iron (FCD)[○] / Copper (Cu)[○] / Brass (Bs)[○] / Brass cast iron (BsC)[○] / Bronze (Pb)[○] / Aluminum Rolled Material (AL)[◎] / Aluminum Alloy Casting (AC, ADC)[○] / Magnesium Alloy (MC)[○] / Zinc Alloy Casting (ZDC)[○] / Thermoplastic plastic (vinyl chloride, nylon, etc.)[○] | Low-Carbon Steel (carbon alloy less than 0.25%)[◎] / Medium carbon steel (carbon content 0.25 to 0.45%)[◎] / High Carbon Steel (C with a content over 0.45%)[◎] / Alloy Steel (SCM)[◎] / Stainless Steel (JIS-SUS)[◎] / Tool Steel (Before SKD Hardening)[○] / Steel casting (SC)[◎] / Ductile Cast Iron (FCD)[◎] / Copper (Cu)[○] / Brass (Bs)[○] / Brass cast iron (BsC)[○] / Bronze (Pb)[○] / Aluminum Rolled Material (AL)[○] / Aluminum Alloy Casting (AC, ADC)[○] / Magnesium Alloy (MC)[○] / Zinc Alloy Casting (ZDC)[○] / Titanium Alloy (Ti-6Al-4V, etc)[○] | Low-Carbon Steel (carbon alloy less than 0.25%)[◎] / Medium carbon steel (carbon content 0.25 to 0.45%)[◎] / High Carbon Steel (C with a content over 0.45%)[◎] / Alloy Steel (SCM)[◎] / Stainless Steel (JIS-SUS)[◎] / Tool Steel (Before SKD Hardening)[○] / Steel casting (SC)[◎] / Ductile Cast Iron (FCD)[◎] / Copper (Cu)[○] / Brass (Bs)[○] / Brass cast iron (BsC)[○] / Bronze (Pb)[○] / Aluminum Rolled Material (AL)[○] / Aluminum Alloy Casting (AC, ADC)[○] / Magnesium Alloy (MC)[○] / Zinc Alloy Casting (ZDC)[○] / Titanium Alloy (Ti-6Al-4V, etc)[○] / Thermoplastic plastic (vinyl chloride, nylon, etc.)[○] | Stainless Steel (JIS-SUS)[◎] / Copper (Cu)[◎] / Thermoplastic plastic (vinyl chloride, nylon, etc.)[◎] | Low-Carbon Steel (carbon alloy less than 0.25%)[◎] / Medium carbon steel (carbon content 0.25 to 0.45%)[◎] / High Carbon Steel (C with a content over 0.45%)[○] / Alloy Steel (SCM)[○] / Stainless Steel (JIS-SUS)[○] / Quenched and tempered steel (25 to 35 HRC)[○] / Quenched and tempered steel (35 to 45 HRC)[○] / Steel casting (SC)[○] / Copper (Cu)[○] / Brass (Bs)[○] / Brass cast iron (BsC)[○] / Aluminum Rolled Material (AL)[○] / Aluminum Alloy Casting (AC, ADC)[◎] / Zinc Alloy Casting (ZDC)[○] / Thermoplastic plastic (vinyl chloride, nylon, etc.)[○] | Low-Carbon Steel (carbon alloy less than 0.25%)[◎] / Medium carbon steel (carbon content 0.25 to 0.45%)[○] / High Carbon Steel (C with a content over 0.45%)[○] / Alloy Steel (SCM)[○] / Steel casting (SC)[○] / Thermoplastic plastic (vinyl chloride, nylon, etc.)[○] | Nickel-based alloy (Inconel, etc.)[◎] | Low-Carbon Steel (carbon alloy less than 0.25%)[○] / Medium carbon steel (carbon content 0.25 to 0.45%)[○] / High Carbon Steel (C with a content over 0.45%)[○] / Alloy Steel (SCM)[○] / Stainless Steel (JIS-SUS)[◎] / Tool Steel (Before SKD Hardening)[○] / Steel casting (SC)[○] / Ductile Cast Iron (FCD)[○] / Copper (Cu)[○] / Brass (Bs)[○] / Brass cast iron (BsC)[○] / Bronze (Pb)[○] / Aluminum Rolled Material (AL)[○] / Aluminum Alloy Casting (AC, ADC)[○] / Magnesium Alloy (MC)[○] / Zinc Alloy Casting (ZDC)[○] / Titanium Alloy (Ti-6Al-4V, etc)[○] / Thermoplastic plastic (vinyl chloride, nylon, etc.)[○] | Low-Carbon Steel (carbon alloy less than 0.25%)[◎] / Medium carbon steel (carbon content 0.25 to 0.45%)[◎] / High Carbon Steel (C with a content over 0.45%)[◎] / Alloy Steel (SCM)[◎] / Stainless Steel (JIS-SUS)[◎] / Tool Steel (Before SKD Hardening)[○] / Steel casting (SC)[◎] / Cast Iron (FC)[○] / Ductile Cast Iron (FCD)[○/◎] / Copper (Cu)[○] / Brass (Bs)[○] / Brass cast iron (BsC)[○] / Bronze (Pb)[○] / Aluminum Rolled Material (AL)[○] / Aluminum Alloy Casting (AC, ADC)[○] / Magnesium Alloy (MC)[○] / Zinc Alloy Casting (ZDC)[○] / Titanium Alloy (Ti-6Al-4V, etc)[○] / Nickel-based alloy (Inconel, etc.)[○] / Thermoplastic plastic (vinyl chloride, nylon, etc.)[○] | Copper (Cu)[○] / Aluminum Rolled Material (AL)[◎] / Aluminum Alloy Casting (AC, ADC)[◎] / Zinc Alloy Casting (ZDC)[◎] | Stainless Steel (JIS-SUS)[◎] / Copper (Cu)[◎] / Thermoplastic plastic (vinyl chloride, nylon, etc.)[◎] | Low-Carbon Steel (carbon alloy less than 0.25%)[◎] / Medium carbon steel (carbon content 0.25 to 0.45%)[○] / High Carbon Steel (C with a content over 0.45%)[○] / Alloy Steel (SCM)[○] / Steel casting (SC)[○] / Thermoplastic plastic (vinyl chloride, nylon, etc.)[○] | Medium carbon steel (carbon content 0.25 to 0.45%)[○] / High Carbon Steel (C with a content over 0.45%)[○] / Alloy Steel (SCM)[○] / Cast Iron (FC)[○] / Ductile Cast Iron (FCD)[○] / Copper (Cu)[○] / Brass (Bs)[○] / Brass cast iron (BsC)[○] / Bronze (Pb)[○] / Aluminum Rolled Material (AL)[◎] / Aluminum Alloy Casting (AC, ADC)[○] / Magnesium Alloy (MC)[○] / Zinc Alloy Casting (ZDC)[○] / Thermoplastic plastic (vinyl chloride, nylon, etc.)[○] | Low-Carbon Steel (carbon alloy less than 0.25%)[◎] / Medium carbon steel (carbon content 0.25 to 0.45%)[◎] / High Carbon Steel (C with a content over 0.45%)[○] / Alloy Steel (SCM)[○] / Stainless Steel (JIS-SUS)[○] / Quenched and tempered steel (25 to 35 HRC)[○] / Quenched and tempered steel (35 to 45 HRC)[○] / Steel casting (SC)[○] / Copper (Cu)[○] / Brass (Bs)[○] / Brass cast iron (BsC)[○] / Aluminum Rolled Material (AL)[○] / Aluminum Alloy Casting (AC, ADC)[◎] / Zinc Alloy Casting (ZDC)[○] / Thermoplastic plastic (vinyl chloride, nylon, etc.)[○] | Low-Carbon Steel (carbon alloy less than 0.25%)[◎] / Medium carbon steel (carbon content 0.25 to 0.45%)[◎] / High Carbon Steel (C with a content over 0.45%)[○] / Alloy Steel (SCM)[○] / Stainless Steel (JIS-SUS)[○] / Quenched and tempered steel (25 to 35 HRC)[○] / Quenched and tempered steel (35 to 45 HRC)[○] / Steel casting (SC)[○] / Copper (Cu)[○] / Brass (Bs)[○] / Brass cast iron (BsC)[○] / Aluminum Rolled Material (AL)[○] / Aluminum Alloy Casting (AC, ADC)[◎] / Zinc Alloy Casting (ZDC)[○] / Thermoplastic plastic (vinyl chloride, nylon, etc.)[○] | Low-Carbon Steel (carbon alloy less than 0.25%)[◎] / Medium carbon steel (carbon content 0.25 to 0.45%)[◎] / Alloy Steel (SCM)[○] / Steel casting (SC)[○] / Thermoplastic plastic (vinyl chloride, nylon, etc.)[○] | High Carbon Steel (C with a content over 0.45%)[◎] / Quenched and tempered steel (25 to 35 HRC)[◎] / Quenched and tempered steel (35 to 45 HRC)[◎] / Tool Steel (Before SKD Hardening)[◎] / Steel casting (SC)[○] / Cast Iron (FC)[○] / Ductile Cast Iron (FCD)[○] / Titanium Alloy (Ti-6Al-4V, etc)[○] / Nickel-based alloy (Inconel, etc.)[○] | High Carbon Steel (C with a content over 0.45%)[◎] / Quenched and tempered steel (25 to 35 HRC)[◎] / Quenched and tempered steel (35 to 45 HRC)[◎] / Tool Steel (Before SKD Hardening)[◎] / Steel casting (SC)[○] / Cast Iron (FC)[○] / Ductile Cast Iron (FCD)[○] / Titanium Alloy (Ti-6Al-4V, etc)[○] / Nickel-based alloy (Inconel, etc.)[○] | Low-Carbon Steel (carbon alloy less than 0.25%)[◎] / Stainless Steel (JIS-SUS)[○] / Copper (Cu)[○] | Low-Carbon Steel (carbon alloy less than 0.25%)[◎] / Medium carbon steel (carbon content 0.25 to 0.45%)[◎] / High Carbon Steel (C with a content over 0.45%)[◎] / Alloy Steel (SCM)[◎] / Stainless Steel (JIS-SUS)[◎] / Tool Steel (Before SKD Hardening)[○] / Steel casting (SC)[◎] / Ductile Cast Iron (FCD)[◎] / Copper (Cu)[○] / Brass (Bs)[○] / Brass cast iron (BsC)[○] / Bronze (Pb)[○] / Aluminum Rolled Material (AL)[○] / Aluminum Alloy Casting (AC, ADC)[○] / Magnesium Alloy (MC)[○] / Zinc Alloy Casting (ZDC)[○] / Titanium Alloy (Ti-6Al-4V, etc)[○] |
| Tap Type | Point tap | Point tap | Point tap | Point tap | Point tap | Point tap | Point tap | Point tap | Point tap | Point tap | Point tap | Point tap | Point tap | Point tap | Point tap | Point tap | Point tap | Point tap | Point tap | Point tap | Point tap |
| Hole type | For through hole | For through hole | For through hole | For through hole | For through hole | For through hole | For through hole | For blind hole | For through hole | For through hole | For through hole | For through hole | For through hole | For through hole | For through hole | For through hole | For through hole | For through hole | For through hole | For through hole | For through hole |
| Coating Y/N | Available | N/A | Available | Available | N/A | Available | N/A | Available | Available | Available | N/A | N/A | N/A | N/A | Available | Available | N/A | N/A | N/A | N/A | Available |
| Coating Type | TiN | Non-Coated | Other | TiCN | Non-Coated | TiN | Non-Coated | Other | TiN | TiCN | Non-Coated | Non-Coated | Non-Coated | Non-Coated | TiN | TiN | Non-Coated | Non-Coated | Non-Coated | Non-Coated | Other |
| Overall Length (L)(mm) | 34 ～ 175 | 30 ～ 185 | 34 ～ 120 | 70 ～ 75 | 34 ～ 175 | 46 ～ 88 | 100 ～ 150 | 70 | 100 ～ 200 | 100 | 40 ～ 62 | 100 ～ 200 | 40 ～ 175 | 80 ～ 300 | 46 ～ 88 | 100 ～ 200 | 40 ～ 95 | 34 ～ 185 | 150 | 34 ～ 82 | 80 ～ 200 |
Loading...
Filter by:
Stock
-
- Stock Items Included
Narrow search by specifying spec./dim.
-
Screw Types
- Meter
- Unified
- Whitworth
- Sewing Machine
-
Screw size (Nominal)
- No0UN
- No.10-32UNF
- No.10-24UNC
- No.2-56UNC
- No.4-48UNF
- No.5-44UNF
- No.5-40UNC
- No.6-40UNF
- No.6-32UNC
- No.8-36UNF
- No.8-32UNC
- 1UN
- G 1"
- M1
- No1UN
- W1
- 1"1/2UN
- W1"1/2
- 1"1/4UN
- W1"1/4
- W1"1/8
- 1/2UN
- G 1/2
- UNC 1/2
- UNF 1/2
- W1/2
- 1/2-20UNF
- 1/2-13UNC
- 1/2W12
- 1/4UN
- G 1/4
- SM1/4
- UNC 1/4
- UNF 1/4
- W1/4
- 1/4-28UNF
- 1/4-20UNC
- 1/4W20
- G 1/8
- SM1/8
- W1/8
- M1.1
- M1.2
- M1.4
- M1.6
- M1.7
- M1.8
- M2
- No2UN
- M2.2
- M2.3
- M2.5
- M2.6
- M3
- No3UN
- STI M3
- 3/4UN
- G 3/4
- UNC 3/4
- UNF 3/4
- W3/4
- 3/4-16UNF
- 3/4-10UNC
- 3/4W10
- 3/8UN
- G 3/8
- UNC 3/8
- UNF 3/8
- W3/8
- 3/8-24UNF
- 3/8-16UNC
- 3/8W16
- M3 - M10
- M3 - M12
- SM3/16
- W3/16
- 3/16W24
- SM3/32
- M3.5
- M4
- No4UN
- STI M4
- №4-40UNC
- M4.5
- M5
- No5UN
- STI M5
- №5-40UNC
- 5/8UN
- UNC 5/8
- UNF 5/8
- W5/8
- 5/8-18UNF
- 5/8-11UNC
- 5/8W11
- M5 - M12
- 5/16UN
- UNC 5/16
- UNF 5/16
- W5/16
- 5/16-24UNF
- 5/16-18UNC
- 5/16W18
- M5.5
- M6
- No6UN
- STI M6
- №6-32UNC
- M7
- 7 execution M3 - M12
- 7/8UN
- UNC 7/8
- UNF 7/8
- W7/8
- 7/8-14UNF
- 7/8-9UNC
- 7/16UN
- UNC 7/16
- UNF 7/16
- 7/16-20UNF
- 7/16-14UNC
- 7/16W14
- M8
- MF8
- No8UN
- STI M8
- №8-32UNC
- M9
- 9/16UN
- 9/16-18UNF
- 9/16-12UNC
- SM9/32
- SM9/64
- M10
- MF10
- No10UN
- STI M10
- №10-32UNF
- №10-24UNC
- M11
- SM11/64
- M12
- MF12
- Mf12
- No12UN
- STI M12
- M12 x 1.5
- M13
- M14
- MF14
- M15
- SM15/64
- M16
- MF16
- Mf16
- M16 x 1.5
- M17
- M18
- MF18
- M19
- M20
- MF20
- Mf20
- M20 x 1.5
- M22
- M23
- M24
- M25
- Mf25
- M25 x 1.5
- M26
- M27
- M28
- M30
- M32
- Mf32
- M33
- M35
- M36
- M39
- M42
- M45
- M48
-
Pitch (P), Number of Threading(mm)
-
Chamfer threads (Lcf)
-
Tool Material Type
-
work material
- Low-Carbon Steel (carbon alloy less than 0.25%)
- Medium carbon steel (carbon content 0.25 to 0.45%)
- High Carbon Steel (C with a content over 0.45%)
- Alloy Steel (SCM)
- Stainless Steel (JIS-SUS)
- Quenched and tempered steel (25 to 35 HRC)
- Quenched and tempered steel (35 to 45 HRC)
- Quenched and tempered steel (45 to 55 HRC)
- High Hardness Steel (50-60 HRC)
- Tool Steel (Before SKD Hardening)
- Steel casting (SC)
- Cast Iron (FC)
- Ductile Cast Iron (FCD)
- Copper (Cu)
- Brass (Bs)
- Brass cast iron (BsC)
- Bronze (Pb)
- Aluminum Rolled Material (AL)
- Aluminum Alloy Casting (AC, ADC)
- Magnesium Alloy (MC)
- Zinc Alloy Casting (ZDC)
- Titanium Alloy (Ti-6Al-4V, etc)
- Nickel-based alloy (Inconel, etc.)
- Thermoplastic plastic (vinyl chloride, nylon, etc.)
-
Tap Type
-
Hole type
-
Coating Y/N
-
Coating Type
-
Overall Length (L)(mm)
Narrow search by specifying Brand
-
- MISUMI (3)
- OSG (21)
- YAMAWA MFG (21)
- SANDVIK (3)
- NACHI(FUJIKOSHI) (2)
- GUHRING (1)
- SKC (1)
- TRUSCO NAKAYAMA (1)
- WERA (0)
- FEIN (0)
- BERNSTEIN AG (0)
- RUKO (0)
- STAHLWILLE (0)
- GEDORE (0)
- HAZET (0)
- REX TOOLS (0)
Narrow search by specifying CAD data type
-
- 2D
- 3D
Categories related to Point Taps
Fizetési mód
Átutalás
Előre fizetés
Igény szerinti gyártás
Tanúsítványok
Copyright © MISUMI Corporation Minden jog fenntartva.