- Diameter d1
- 31
- Identification No.
- Finish
- Thread d3
- Thread d4
- d5
- d6
- 18
- d7
- 14
- d8
- 3.5
- r1
- 21.5
- r2
- 32.5
- h1
- 35.5
- h2
- 29.6
- h3
- 14.9
- k
- 36
- l2
- 22
- m
- 9
- sw1
- 12
- x16
- 2.5
- x17
- 6.5
- r1
- 21.5
- Type
- 784
- CAD
- 2D
- 3D
- Becsült szállítási napok
- Minden
- Aznapi feladás lehetséges
Swivel ball joints (784-31-1/4-A-1-ELS)
Termékadatok
GN 784 / Swivel Ball Joints, Aluminum
Information
GN 784 Swivel ball joints allow precise and variable adjustment of the ball pivot within the rotation range. This is a particular advantage when adjusting scanners, cameras, lighting, monitors, etc.
Thanks to the efficient clamping mechanism, only small amounts of torque on the clamping screw result in comparatively strong clamping pressure on the ball. This force is easily applied by the clamping lever (Identification no. 1).
The ball joint can be mounted from below with the d5 internal thread or together with the GN 784.1 flange, available as an accessory, using three through-holes from above.
For a permanent high stop torque, the contact surfaces of the balls must be kept free of grease. Exceeding the recommended tightening torque increases the securing of the ball joint in its end position, but may result in increased wear and potential failure of the clamping mechanism.
see also...
• Flanges GN 784.1
How to Order
How to order (with female thread) | 1 | d1 |
| 2 | d3 (d2) | |
| 3 | Type | |
| 4 | Identification no. | |
| 5 | Finish |
How to order (with male thread) | 1 | d1 |
| 2 | d4 | |
| 3 | Type | |
| 4 | Identification no. | |
| 5 | Finish |
Specification 
Aluminum
anodized black ELS
• Base plate, ball
Aluminum, blank
• Adjustable hand lever (Identification no. 1)
- Zinc die casting
plastic coated
silver, RAL 9006, textured finish
- Threaded stud and retaining screw
Stainless Steel AISI 303
• Set screw (Identification no. 2)
Stainless Steel AISI 304
• Stainless Steel characteristics
• RoHS compliant
On request
Dimensions
 |  | | | ||||||
| d1 | d2* | r1 | d3** | r2 | d4 | r1 | l1 | ||
| Type A | Type A | Type B | |||||||
| Inch thread | Inch thread | ||||||||
| 23 | M 4 | 17.3 | M 5 | - | 24.8 | M 5 | - | 17.3 | 8 |
| 23 | - | - | - | 1/4 (≙ 1/4-20) | 24.8 | M 6 | 1/4 (≙ 1/4-20) | 17.3 | 10 |
| 31 | M 5 | 21.5 | M 6 | 1/4 (≙ 1/4-20) | 32.5 | M 6 | 1/4 (≙ 1/4-20) | 21.5 | 10 |
| 31 | - | - | - | - | 32.5 | M 8 | - | 21.5 | 12 |
| 39 | M 5 | 25.5 | M 6 | - | 36.2 | M 6 | - | 25.5 | 10 |
| 39 | - | - | M 8 | 3/8 (≙ 3/8-16) | 40.5 | M 8 | 3/8 (≙ 3/8-16) | 25.5 | 12 |
| 49 | M 8 | 30.8 | - | 3/8 (≙ 3/8-16) | 44.8 | M 8 | 3/8 (≙ 3/8-16) | 30.8 | 12 |
| 49 | - | - | M 10 | - | 51.8 | M 10 | - | 30.8 | 15 |
| d1 | d5*** | d6 | d7 | d8 | h1 | h2 | h3 | k | l2 | m | A/F1 | A/F2 | recommended tightening torque of the clamping (Identification no.) in Nm ≈ | resulting stop torque on the ball in Nm ≈ |
| 23 | M 5 | 14 | 11 | 2.5 | 26.6 | 21.7 | 10.6 | 32 | 22 | 7 | 9 | 2.5 | 1.5 | 4.5 |
| 31 | M 6 | 18 | 14 | 3.5 | 35.5 | 29.6 | 14.9 | 36 | 22 | 9 | 12 | 3 | 2.5 | 6.5 |
| 39 | M 8 | 24 | 15 | 4.5 | 45 | 37.2 | 18.9 | 44 | 30 | 12 | 13 | 4 | 4 | 16 |
| 49 | M 8 | 28 | 19.5 | 4.5 | 56 | 46.1 | 24 | 49 | 30 | 16 | 17 | 4 | 4 | 20 |
Részletes információk
Alapvető információk
GN 784 swivel ball joints allow precise and variable adjustment of the ball pivot within the rotation range. This is a particular advantage when adjusting scanners, cameras, lighting, monitors, etc.
Thanks to the efficient clamping mechanism, only small amounts of torque on the clamping screw result in comparatively strong clamping pressure on the ball. This force is easily applied by the clamping lever (Identification no.1).
The ball joint can be mounted from below with the d5 internal thread or together with the GN 784.1 flange, available as an accessory, using three through-holes from above.
For a permanent high stop torque, the contact surfaces of the balls must be kept free of grease. Exceeding the recommended tightening torque increases the securing of the ball joint in its end position, but may result in increased wear and potential failure of the clamping mechanism.