Szűrési feltételek
- External Dimension A(mm)[20–200/1mm egység]
- External Dimension B(mm)[15–100/1mm egység]
- External Dimension L(mm)[15–100/1mm egység]
- H(mm)[0–200/1mm egység]
- Hole Configurable 1, Screw Through Hole Nominal Dia. Selection [N]
- 3
- 4
- 5
- 6
- 8
- 10
- Hole Configurable 1, Tapped Hole [M](mm)
- 3
- 4
- 5
- 6
- 8
- 10
- Hole Configurable 2, Screw Through Hole Nominal Dia. Selection [NA]
- 3
- 4
- 5
- 6
- 8
- 10
- Hole Configurable 2, Tapped Hole [MA](mm)
- 3
- 4
- 5
- 6
- 8
- 10
- Plate Thickness t(mm)
- 2
- 2.3
- 3
- 3.2
- 4
- 4.5
- S(mm)[0–100/1mm egység]
- CAD
- 2D
- 3D
- Becsült szállítási napok
- Minden
- 7 munkanapok belül
- 9 munkanapok belül
L-Shaped Sheet Metal Mounting Plate / Bracket -Hole Position Center Distribution Type- FSLAS
Cikkszám:
javaslat található.Vázlatrajz és specifikációs táblázat
Dimensional Drawing
■Hole Type Selection Chart
| Hole Type | Bolt Hole | Tapped Hole(Coarse) |
| Code | N・NA | M・MA |
| Shape Diagram |  |  |
| [ ! ] For the d dimensions, refer to the "N, NA Machining Dimension Table" section below the Specifications Table. |
| Part Number | [ M ]Material | [ S ]Surface Treatment | ||
| Type | Material Symbol | |||
| FSLAS | SP | T0.8 to 3.2 T4.5 to 6.0 T9.0 | : EN 1.0330 Equiv. : EN 1.0320 Equiv. (hot coiled) : EN 1.0038 Equiv.(Black) | － |
| SPU | Trivalent Chromate (Clear) | |||
| SPK | Trivalent Chromate (Black) | |||
| AM | EN AW−5052 Equiv. | － | ||
| AMW | Anodize (Clear) | |||
| AMB | Anodize (Black) | |||
| SUD | T0.8 to 6.0 T9.0 | : EN 1.4301 Equiv. (Passivated 2B) : EN 1.4301 Equiv.(No.1) | － | |
Specification Table
| Part Number | － | T | － | A | － | B | － | L | － | H | － | Hole Specification① Code / Nominal Dia. | － | S | － | Hole Specification② Code / Nominal Dia. | ||
| Type | － | Material Symbol | ||||||||||||||||
| FSLAS | － | SP | － | T2.3 | － | A30 | － | B30 | － | L25 | － | H20 | － | N5 | － | S15 | － | NA5 |
| Part Number | Selection | 1 mm Increments | H | Hole Specification① | S | Hole Specification② | |||||||||
| Type | Material Symbol | T | A | B | L | Code / Specify Method | Code / Specify Method | ||||||||
| FSLAS | SP SPU SPK | 0.8 ・ 1.0 ・ 1.2 ・ 1.6 ・ 2.3 3.2 ・ 4.5 ・ 6.0 ・ 9.0 | 20 to 200 | 15 to 100 [ ! ] | 15 to 100 [ ! ] | 1 mm Increments | N (Bolt Hole)＊ 3・4・5 6・8・10 (Select) [ ! ] | M (Tapped Hole) 3・4・5 6・8・10 (Select) [ ! ] | 1 mm Increments | NA (Bolt Hole)＊ 3・4・5 6・8・10 (Select) [ ! ] | MA (Tapped Hole) 3・4・5 6・8・10 (Select) [ ! ] | ||||
| AM AMW AMB | 1.0 ・ 1.5 ・ 2.0 ・ 3.0 ・ 4.0 ・ 5.0 | ||||||||||||||
| SUD | 0.8 ・ 1.0 ・ 1.2 ・ 1.5 ・ 2.0 3.0 ・ 4.0 ・ 5.0 ・ 6.0 ・ 9.0 | ||||||||||||||
| [ ! ] For T6.0, B≧20, L≧20 | |||||||||||||||
| [ ! ] For T9.0, B≧32, L≧20 | |||||||||||||||
| [ ! ] Holes may deform if the hole locations are too close to the ends and bends, but they will be machined as specified if they are within the machining limits. | |||||||||||||||
[ ! ] N・NA Machining Dimension Table
| N・NA Specified Value | Through Hole Diameter(d) |
| 3 | 3.5 |
| 4 | 4.5 |
| 5 | 5.5 |
| 6 | 6.5 |
| 8 | 9 |
| 10 | 11 |
[ ! ] Hole Machining Table
[ ! ]T = 1.0 is not applicable to AM, AMW, or AMB
| T | N・NA (Bolt Hole) | M・MA (Tapped Hole) |
| 0.8 | 3・4・5・6・8・10 | Not Possible |
| 1.0、1.2 | 3 | |
| 1.5、1.6 | 3・4 | |
| 2.0、2.3 | 3・4・5・6 | |
| 3.0、3.2 | 3・4・5・6・8 | |
| 4.0 to 6.0 | 3・4・5・6・8・10 | |
| 9.0 | 5・6・8・10 | 5・6・8・10 |
Specifications, Machining Limits
[ ! ] 1. Burr height 0.1 or less
[ ! ] 2. Bend angle tolerance ±1°
[ ! ] 3. In case of the thin plates, the tap ridges may be crushed, so please be careful when tightening.
[ ! ] 4. There are machining limits for sections b, f, g below.
[ ! ] Slotted hole f parallel to T4.0 and T4.5 will be (9).
[ ! ] The hole may be deformed if specified at the limit value shown above.
[ ! ] 5. There will be some scratches left by press brake. Use r, e, d dimension for reference only.
[ ! ] If the bend and hole are close to each other, r may be smaller.[ ! ] 6. Bending causes biting and bulging.
[ ! ] 7. Since it is manufactured with minimum bending R, there is a possibility of breakage if it is used in an environment where stress is concentrated, such as impact.
[ ! ] 2. Bend angle tolerance ±1°
[ ! ] 3. In case of the thin plates, the tap ridges may be crushed, so please be careful when tightening.
[ ! ] 4. There are machining limits for sections b, f, g below.
| T | f (Distance between the hole and the bend) | b (Distance between the hole and the end face) | g | ||||||
| EN 1.0330 Equiv. EN 1.0320 Equiv. (hot coiled) EN 1.0038 Equiv. | EN AW−5052 Equiv. | EN 1.4301 Equiv. | Through Hole | Tapped Hole | Slotted Hole parallel to Hole Bending with Tolerance | ||||
| L Bend | Z, Convex Bend | L Bend | Z, Convex Bend | ||||||
| 0.8 | ー | 0.8 | 2 | 3 | ー | ー | 3.5 | 1 | 5 |
| 1.0 | 1.0 | 1.0 | 2 | 3 | 3 | 5.5 | 3.5 | 1 | 5.5 |
| 1.2 | ー | 1.2 | 2 | 3 | 3 | 5.5 | 3.5 | 1 | 5.5 |
| 1.6 | 1.5 | 1.5 | 2 | 3.5 | 3 | 6 | 4 | 1 | 6 |
| 2.3 | 2.0 | 2.0 | 2 | 4.5 | 3 | 7 | 5 | 1.5 | 7 |
| 3.2 | 3.0 | 3.0 | 2 | 6.5 | 3 | 9 | 7 | 1.5 | 9 |
| 4.5 | 4.0 | 4.0 | 3 | 7.5 | 4 | 11 | 8(9) | 2 | 11 |
| ー | 5.0 | 5.0 | 3 | 14 | 4 | 16 | 15 | 2.5 | 18 |
| 6.0 | ー | 6.0 | 3 | 14 | 4 | 16 | 15 | 2.5 | 18 |
| 9.0 | ー | 9.0 | 20 | ー | 20.5 | ー | 20 | 4 | 20 |
[ ! ] The hole may be deformed if specified at the limit value shown above.
| T | R after Bending | Brake Scratches | |||
| Position | Depth | ||||
| EN 1.0330 Equiv. EN 1.0320 Equiv. (hot coiled) EN 1.0038 Equiv. | EN AW−5052 Equiv. | EN 1.4301 Equiv. | （r） | （e） | （d） |
| 0.8 | ー | 0.8 | 0.8 | 5 | 0.1 |
| 1.0 | 1.0 | 1.0 | 1 | 5 | 0.1 |
| 1.2 | ー | 1.2 | 1.2 | 5 | 0.1 |
| 1.6 | 1.5 | 1.5 | 1.5 | 6 | 0.1 |
| 2.3 | 2.0 | 2.0 | 2.0 | 7.5 | 0.1 |
| 3.2 | 3.0 | 3.0 | 3.0 | 10.5 | 0.2 |
| 4.5 | 4.0 | 4.0 | 4.0 | 13.5 | 0.3 |
| ー | 5.0 | 5.0 | 5.0 | 17 | 0.5 |
| 6.0 | ー | 6.0 | 6.0 | 17 | 0.5 |
| 9.0 | ー | 9.0 | 9.0 | 27 | 0.8 |
■Appearance per Material (Surface Treatment) and Machining Method
| N/A | Black Oxide | Trivalent Chromate (White) | Trivalent Chromate (Black) | |
| SP | SPB | SPU | SPK | |
| EN 1.0330 Equiv. T0.8 to 3.2 |  |  |  |  |
| EN 1.0320 Equiv. (hot coiled) T4.5 to 6.0 |  |  |  |  |
| EN 1.0038 Equiv. (Black) T9.0 |  |  |  |  |
| N/A | Anodize (Clear) | Anodize (Black) | |
| AM | AMW | AMB | |
| EN AW−5052 Equiv. |  |  |  |
| N/A | |
| SUD | |
| EN 1.4301 Equiv. (Passivated 2B) T0.8 to 6.0 |  |
| EN 1.4301 Equiv.（No.1） T9.0 |  |
Cikkszámlista
Elemek száma
| Cikkszám |
|---|
Egységár (HÉA nélkül)(egységár adóval) | Normál feladási dátum |
|---|
- ( - ) | 7 munkanapok |
- ( - ) | 7 munkanapok |
- ( - ) | 7 munkanapok |
- ( - ) | 7 munkanapok |
- ( - ) | 9 munkanapok |
- ( - ) | 9 munkanapok |
- ( - ) | 9 munkanapok |
- ( - ) | 9 munkanapok |
- ( - ) | 9 munkanapok |
- ( - ) | 9 munkanapok |
- ( - ) | 9 munkanapok |
- ( - ) | 9 munkanapok |
- ( - ) | 7 munkanapok |
- ( - ) | 7 munkanapok |
- ( - ) | 7 munkanapok |
- ( - ) | 7 munkanapok |
- ( - ) | 7 munkanapok |
- ( - ) | 7 munkanapok |
- ( - ) | 7 munkanapok |
- ( - ) | 7 munkanapok |
- ( - ) | 7 munkanapok |
- ( - ) | 7 munkanapok |
- ( - ) | 7 munkanapok |
- ( - ) | 7 munkanapok |
- ( - ) | 7 munkanapok |
- ( - ) | 7 munkanapok |
- ( - ) | 7 munkanapok |
- ( - ) | 7 munkanapok |