Rotary Axes / Offset on One Side, External Thread / Optional Machining (Part Numbers - CAD Download)

MISUMI

Order quantities extended (D-JIT)

Part Number

Once your search is narrowed to one product,
the corresponding part number is displayed here.

Drawing / Specifications
3D Preview 3D preview is available after complete configuration
Part Numbers
More Information
Catalog
Technical Information

Dimensional Drawing

■ Standard

■Wrench Flats

[ ! ] Surface roughness of Part D for h9 (Cold-drawn) is {{{attr2}}} . Surface roughness for h7 (Ground) and g6 (Ground) is {{{attr3}}} .
[ ! ] High hardness stainless steel may have a center hole.

■Tolerance Table

D·P	h9 (Cold-drawn)	h7 (Ground)	g6 (Ground)
3	0 − 0.025	0 − 0.010	− 0.002
			− 0.008
3.1 to 6	0 − 0.030	0 − 0.012	− 0.004
			− 0.012
6.1 to 10	0 − 0.036	0 − 0.015	− 0.005
			− 0.014
10.1 to 18	0 − 0.043	0 − 0.018	− 0.006
			− 0.017
18.1 to 30	0 − 0.052	0 − 0.021	− 0.007
			− 0.020
30.1 to 50	0 − 0.062	0 − 0.025	− 0.009
			− 0.025

Rotary Shaft - One End Stepped, One End Threaded, Dimensional Drawing 2

■Circularity and Straightness

■Concentricity and Perpendicularity

■Circularity of Part D

D		Circularity M
over	or Less	Circularity M
5	13	0.004
13	20	0.005
20	40	0.006
40	50	0.007

■Tolerances of L and Other Dimensions

Dimension		Dimension Tolerance
over	or Less	Dimension Tolerance
2	6	±0.1
6	30	±0.2
30	120	±0.3
120	400	±0.5
400	1000	±0.8

[ ! ] Circularity, straightness, concentricity, and perpendicularity of Part D are not applicable to h9 (Cold-drawn).

Type			Tolerance		[M] Material	[S] Surface Treatment
	Standard	Wrench Flats	D	P	[M] Material	[S] Surface Treatment
(1)	NSFRMHN	NSFRMHNS	h9 (Cold-drawn)	h7	EN 1.1191 Equiv.	—
	SFRMHN	SFRMHNS				Black Oxide
	PSFRMHN	PSFRMHNS				Electroless Nickel Plating
	SSFRMHN	SSFRMHNS			EN 1.4301 Equiv.	—
(2)	NSFRMGN	NSFRMGNS		g6	EN 1.1191 Equiv.	—
	SFRMGN	SFRMGNS				Black Oxide
	PSFRMGN	PSFRMGNS				Electroless Nickel Plating
	SSFRMGN	SSFRMGNS			EN 1.4301 Equiv.	—
(3)	NSFRHN	NSFRHNS	h7 (Ground)	h7	EN 1.1191 Equiv.	—
	SFRHN	SFRHNS				Black Oxide
	PSFRHN	PSFRHNS				Electroless Nickel Plating
	SSFRHN	SSFRHNS			EN 1.4301 Equiv.	—
(4)	NSFRN	NSFRNS	g6 (Ground)	g6	EN 1.1191 Equiv.	—
	SFRN	SFRNS				Black Oxide
	PSFRN	PSFRNS				Electroless Nickel Plating
	SSFRN	SSFRNS			EN 1.4301 Equiv.	—
	HFRN	HFRNS			EN 1.7220 Equiv. [H]Hardness: 30 to 35HRC	Black Oxide
	PHFRN	—			EN 1.7220 Equiv. [H]Hardness: 30 to 35HRC	Electroless Nickel Plating
	AHFRN	AHFRNS			High Hardness Stainless Steel Hardness: 35HRC or More	—

[!] High hardness stainless steel has a lower center hardness.

Specification Table

	Part Number	—	L	—	F	—	B	—	P	—	SC
(1) D Tol. h9 / P Tol. h7 (3) h7 (Ground) with Wrench Flat (4) g6 (Ground)	SFRMHN30 SFRHNS25 SF−PSFRN20	— — —	250 200 200	— — —	F30 F25 F20	— — —	B8 B15 B10	— — —	P10 P12 P10	—	SC30

Part Number	—	L	—	F	—	B	—	P	—	SC
SFRMHN30 SFRHNS25 SF−PSFRN20	— — —	250 200 200	— — —	F30 F25 F20	— — —	B8 B15 B10	— — —	P10 P12 P10	—	SC30

(1) D Tolerance h9 (Cold-drawn) / P Tolerance h7 (2) D Tolerance h9 (Cold-drawn) / P Tolerance g6

Part Number			0.1 mm Increments		1 mm Increments	P (Coarse) Selection											1 mm Increments	W	ℓ₂	(Y) max.
Type		D	L	F	B												SC Wrench Flats Type only
Standard	Wrench Flats	D	L	F	B												SC Wrench Flats Type only
(1) D Tol. h9 / P Tol. h7 NSFRMHN SFRMHN PSFRMHN SSFRMHN (D13, 17, 18 or 22 is not available for SSFRMHN.) 　 (2) D Tol. h9 / P Tol. g6 NSFRMGN SFRMGN PSFRMGN SSFRMGN (D13, 17, 18 or 22 is not available for SSFRMGN.)	(1) D Tol. h9 / P Tol. h7 NSFRMHNS SFRMHNS PSFRMHNS SSFRMHNS (D13, 17, 18 or 22 is not available for SSFRMHNS.) 　 (2) D Tol. h9 / P Tol. g6 NSFRMGNS SFRMGNS PSFRMGNS SSFRMGNS (D13, 17, 18 or 22 is not available for SSFRMGNS.)	6	15.0 to 495.0	5 ≤ F ≤ P × 7	B=0 or When P ≤ 6, B ≤ P × 3 & B ≤ F−2 When P = 8, 10, B ≤ P × 3 & B ≤ F−3 When P ≥ 12, B ≤ P × 3 & B ≤ F−5 [ ! ] B ≥ Pitch × 3	3	4	5									SC+ℓ₂ ≤ L SC = 0 or SC ≥ 1	5	8	500
		8	15.0 to 495.0			3	4	5	6									7		500
		10	15.0 to 795.0			3	4	5	6	8								8		800
		12	15.0 to 895.0			3	4	5	6	8	10							10	10	900
		13	15.0 to 895.0				4	5	6	8	10							11		900
		15	15.0 to 995.0				4	5	6	8	10	12						13		1000
		16	15.0 to 995.0				4	5	6	8	10	12						14
		17	24.0 to 995.0					5	6	8	10	12						14
		18	24.0 to 995.0					5	6	8	10	12	16					15
		20	24.0 to 995.0					5	6	8	10	12	16					17
		22	24.0 to 995.0					5	6	8	10	12	16	20				19
		25	24.0 to 995.0					5	6	8	10	12	16	20				22
		30	24.0 to 995.0							8	10	12	16	20	24			27	15
		35	40.0 to 995.0								10	12	16	20	24	30		30	15	1000

[ ! ] When B ≤ P × 1, the threaded portion may be too short and may not function as a thread.

(3) h7 (Ground)

Part Number			0.1 mm Increments		1 mm Increments	P (Coarse) Selection											1 mm Increments	W	ℓ₂	(Y) max.
Type		D	L	F	B												SC Wrench Flats Type only
Standard	Wrench Flats	D	L	F	B												SC Wrench Flats Type only
NSFRHN SFRHN PSFRHN SSFRHN	NSFRHNS SFRHNS PSFRHNS SSFRHNS	6	15.0 to 495.0	5 ≤ F ≤ P × 7	B=0 or When P ≤ 6, B ≤ P × 3 & B ≤ F−2 When P = 8, 10, B ≤ P × 3 & B ≤ F−3 When P ≥ 12, B ≤ P × 3 & B ≤ F−5 [ ! ] B ≥ Pitch × 3	3	4	5									SC+ℓ₂ ≤ L SC = 0 or SC ≥ 1	5	8	500
		8	15.0 to 495.0			3	4	5	6									7		500
		10	15.0 to 795.0			3	4	5	6	8								8		800
		12	15.0 to 895.0			3	4	5	6	8	10							10	10	900
		15	15.0 to 995.0				4	5	6	8	10	12						13		1000
		17	24.0 to 995.0					5	6	8	10	12						14
		20	24.0 to 995.0					5	6	8	10	12	16					17
		25	24.0 to 995.0					5	6	8	10	12	16	20				22
		30	24.0 to 995.0							8	10	12	16	20	24			27	15
		35	40.0 to 995.0								10	12	16	20	24	30		30	15	1000
		40	40.0 to 995.0									12	16	20	24	30		36	20
		50	40.0 to 995.0										16	20	24	30		41	20

[ ! ] When B ≤ P × 1, the threaded portion may be too short and may not function as a thread.

(4) g6 (Ground)

Part Number				0.1 mm Increments		1 mm Increments	P (Coarse) Selection											1 mm Increments	W	ℓ₂	(Y) max.
Type		D		L	F	B												SC Wrench Flats Type only
Standard	Wrench Flats	D		L	F	B												SC Wrench Flats Type only
NSFRN SFRN PSFRN SSFRN * HFRN (D15, 20, 25, 30, 35, 40 or 50 is available for HFRN.) 　 * PHFRN (D15, 20, 25, 30, 35, 40 or 50 is available for PHFRN.) AHFRN (Only * marked sizes are available.)	NSFRNS SFRNS PSFRNS SSFRNS * HFRNS (D15, 20, 25, 30, 35, 40 or 50 is available for HFRNS.) 　 AHFRNS (Only * marked sizes are available.)	*	6	15.0 to 495.0	5 ≤ F ≤ P × 7	B=0 or When P ≤ 6, B ≤ P × 3 & B ≤ F−2 When P = 8, 10, B ≤ P × 3 & B ≤ F−3 When P ≥ 12, B ≤ P × 3 & B ≤ F−5 [ ! ] B ≥ Pitch × 3	3	4	5									SC+ℓ₂ ≤ L SC = 0 or SC ≥ 1	5	8	500
		*	8	15.0 to 495.0			3	4	5	6									7		500
		*	10	15.0 to 795.0			3	4	5	6	8								8		800
		*	12	15.0 to 895.0			3	4	5	6	8	10							10	10	900
			13	15.0 to 895.0				4	5	6	8	10							11		900
		*	15	15.0 to 995.0				4	5	6	8	10	12						13		1000
		*	16	15.0 to 995.0				4	5	6	8	10	12						14
			17	24.0 to 995.0					5	6	8	10	12						14
			18	24.0 to 995.0					5	6	8	10	12	16					15
		*	20	24.0 to 995.0					5	6	8	10	12	16					17
			22	24.0 to 995.0					5	6	8	10	12	16	20				19
		*	25	24.0 to 995.0					5	6	8	10	12	16	20				22
			30	24.0 to 995.0							8	10	12	16	20	24			27	15
			35	40.0 to 995.0								10	12	16	20	24	30		30	15	1000
			40	40.0 to 995.0									12	16	20	24	30		36	20
			50	40.0 to 995.0										16	20	24	30		41	20

[ ! ] When D - P ≤ 2, chamfer C at the step is 0.2 or less.
[ NG ] For D dim. 35 to 50 of HFRN/PHFRN, the upper limit for the total length (Y dim.) is 800.
[ NG ] For D dim. 10 to 25 of AHFRN/AHFRNS, the upper limit for the total length (Y dim.) is 800.
[ ! ] When B ≤ P × 1, the threaded portion may be too short and may not function as a thread.

Coarse Thread Pitch
M (P)	Pitch
3	0.5
4	0.7
5	0.8
6	1.0
8	1.25
10	1.5
12	1.75
16	2.0
20	2.5
24	3.0
30	3.5

Fine Thread Pitch
M (PMC)	Pitch
3	0.35
4	0.5
5	0.5
6	0.75
8	1.0
10
12
15
17
20
25	1.5
30
35
40

Alterations

Alterations
Code

Alteration Details

Applicable Conditions

Ordering Example

Keyway at One Location

KC, A = 0.1 mm Increments

[ ! ] When the keyway position is less than 1 mm away from the end face,
R is not applied.

[ ! ] Key Length ≤ 100
[ NG ] Not applicable when Shaft Dia. ≤ ø5

SSFRHN30-250-F30-B25-P20-KC20-A10

WKC

Keyways at Two Locations

WKC, C, K, E = 0.1 mm Increments

[ ! ] When the keyway position is less than 1 mm away from the end face,
R is not applied.

[ ! ] Key Length ≤ 100
[ NG ] Not applicable when Shaft Dia. ≤ ø5

SSFRHN30-250-F30-B25-P20-WKC5-C20-K5-E10

Keyway (1 Location (for 4th Location))

KZ, Z = 0.1 mm Increments

[ ! ] When the keyway position is less than 1 mm away from the end face,
R is not applied.

[ ! ] Key Length ≤ 100 [ NG ] Not applicable when Shaft Dia. ≤ ø5
[ ! ] Applicable only when combined with both KC and WKC

SSFRHN30-250-F30-B25-P20-KC5-A10-WKC20-C10-K60-E10-KZ100-Z10

PKC

Keyway on Step P (0 Point on the End Face)

PKC = 0.1 mm Increments
[ ! ] Keyway Length ≤ 70
[ NG ] Not applicable when P ≤ 5

SSFRHN30-250-F30-B25-P20-PKC20.0

Keyway on Step P (Position Specification)

PP, PK = 0.1 mm Increments
[ ! ] Keyway Length ≤ 70
[ NG ] Not applicable when P ≤ 5

SSFRHN30-250-F30-B25-P20-PP10-PK10

Multiple Keyways on Step P

PP, PK = 0.1 mm Increments
[ ! ] Keyway Length ≤ 70
[ NG ] Not applicable when P ≤ 5
[ ! ] This alteration is available only when PP is specified

SSFRHN30-250-F30-B25-P20-PP5-PK5-PV15-PW10

Set Screw Flat at One Location

FC, G = 1 mm Increments
[ ! ]G ≤ 70

SSFRHN30-250-F30-B25-P20-FC10-G6

WFC

Set Screw Flats at Two Locations

WFC, J, W, V = 1 mm Increments
[ ! ]J·V ≤ 70

SSFRHN30-250-F30-B25-P20-WFC10-J15-W10-V20

SFC

Set Screw Flat, 2 Set Screw Flats (Angle Specified)

SFC, SG = 1 mm Increments AG = 15° Increments
[ ! ]SG ≤ 70

SSFRHN30-250-F30-B25-P20-SFC10-SG6-AG120

PFC

Set Screw Flat on Step

PFC, LC = 1 mm Increments
[ ! ]LC ≤ 70

SSFRHN30-250-F30-B0-P20-PFC10-LC10

TL·TR

Retaining Ring Groove on D Part

TL, TR = 0.1 mm Increments
[ ! ]2 ≤ TL+F ≤ 150 2 ≤ TR ≤ 150

SSFRHN30-250-F30-B25-P20-TL5-TR5

Retaining Ring Groove on Step

TF = 0.1 mm Increments
[ ! ]2 ≤ TF ≤ 150

SSSFRHN30-250-F30-B25-P20-TF5

PLM

Change Thread to Left-Hand Thread

Changes Right-Hand Thread to Left-Hand Thread.
[ NG ] Combination with PMC is not applicable

SSFRHN30-250-F30-B25-P20-PLM

PMC

Changes to Fine Thread

Changes the Coarse Thread to Fine Thread.
Specify PMC instead of P

SSFRHN30-250-F30-B25-PMC20

Slit Cam Groove

UC = 1 mm Increments
[ NG ] Not applicable when Shaft Dia. = ø2 or ø2.5 or when D ≥ 13
[ NG ] Not available for AHFRN/AHFRNS

SSFRHN10-250-F30-B25-P8-UC10

LKC

L Dimension Tolerance Change

L < 500···L±0.05 L ≥ 500···L±0.1
[ NG ] Not applicable when L ≥ 800

SSFRHN30-250-F30-B25-P20-LKC

Slit Groove Alterations

Slot groove is added to D dimensioned section.　
[ NG ] Not applicable when D dim. ≥ 35

D	N	V
6 to 13	1.2	1.5
15 to 20	2.0	2.5
22 to 30	3.0	3.8

SSFRHN30-250-F30-B25-P20-MM

CKC

Concentricity

Change the concentricity to 0.02.
[ NG ] Not applicable when D Tol. = h9
[ NG ] Not available for AHFRN/AHFRNS
[ ! ] For Lmax, see the table on the right

D	Lmax
6 to 22	450
25 to 50	600

SSFRHN30-250-F30-B25-P20-CKC

Changes Part D Chamfering

Changes Part D Chamfering Size　
* Select CD from table
[ ! ] Only values provided on the Applicable Dia. Table are applicable

Chamfering (CD)	Applicable Dia. (D)
C2	⌀6 to ⌀50
C3	⌀8 to ⌀50
C4	⌀10 to ⌀50
C5	⌀12 to ⌀50

SSFRHN30-250-F30-B52-P20-CD2

Undercut Dimensions

Adds an undercut on P.
[ NG ] Not applicable when D = P

SSFRHN30-250-F30-B25-P20-PC

[!] When combined with other alterations, ± 2 degree phase differential may occur. Provide 2 mm or more clearance between this alteration and others.
[ ! ] When multiple keyways or set screw flats are specified, they are added in the same plane. When the distance of the alterations are over 500 mm, ± 2 degree phase difference may occur.

Keyway Dimensions

Shaft Dia.	b		t		r
Shaft Dia.	Reference Dimension	Tolerance (N9)	Reference Dimension	Tolerance	r
6 to 7	2	-0.004 -0.029	1.2	+0.1 0	0.08 to 0.16
8 to 10	3	-0.004 -0.029	1.8
11 to 12	4	0 -0.03	2.5
13 to 17	5		3.0		0.16 to 0.25
18 to 22	6		3.5
23 to 30	8	0 -0.036	4.0	+0.2 0
31 to 38	10	0 -0.036	5.0		0.25 to 0.4
39 to 44	12	0 -0.043	5.0
45 to 50	14	0 -0.043	5.5

Rotary Shaft - One End Stepped, One End Threaded Dimensional Drawing 4

[ ! ] b ≤ A, E, C ≤ 100
[ ! ] If 3 keyways are required, use both KC and WKC.
[!] If 4 keyways are required, use KC, WKC, and KZ. (KZ is applicable only when combined with both KC and WKC)
[NG] Not applicable to D = 2 to 5.
[ ! ] The example below shows the keyway shape for the specs KC, WKC, K = 0, KC + A ≥ L and WKC + C + K + E > L.

[ ! ] Although keyway(s) and set screw flats are added in the same plane, ±2 degree phase differential may occur.
[ ! ] When the keyway position is less than 1 mm away from the end face, R is not applied.

Detailed Retaining Ring Groove Dimensions for Rotary Shafts

Shaft Dia.	d Tolerance		Slot Width (m) Tolerance		Applicable Retaining Ring
2	1.2	+0.06 0	0.4	+0.05 0	JIS E Type 1.2
2.5	1.5		0.5		JIS E Type 1.5
3	2		0.5		JIS E Type 2
4	3		0.7	+0.1 0	JIS E Type 3
5	4	+0.075 0			JIS E Type 4
6	5				JIS E Type 5
7	6		0.9		JIS E Type 6
8	7	+0.09 0			JIS E Type 7
9	8	+0.09 0			JIS E Type 8
10	9.6	0/－0.09	1.15	+0.14 0	JIS C Type 10
11	10.5	0 -0.11			JIS C Type 11
12	11.5				JIS C Type 12
13	12.4				JIS C Type 13
14	13.4				JIS C Type 14
15	14.3				JIS C Type 15
16	15.2				JIS C Type 16
17	16.2				JIS C Type 17
18	17		1.35		JIS C Type 18
19	18		1.35		JIS C Type 19

Shaft Dia.	d Tolerance		Slot Width (m) Tolerance		Applicable Retaining Ring
20	19	0 -0.21	1.35	+0.14 0	JIS C Type 20
21	20				JIS C Type 21
22	21				JIS C Type 22
23	22				JIS C Type 23
24	22.9				JIS C Type 24
25	23.9				JIS C Type 25
26	24.9				JIS C Type 26
28	26.6		1.65		JIS C Type 28
29	27.6				JIS C Type 29
30	28.6				JIS C Type 30
32	30.3	0 -0.25			JIS C Type 32
35	33				JIS C Type 35
40	38		1.9		JIS C Type 40
45	42.5		1.9		JIS C Type 45
50	47		2.2		JIS C Type 50

[ ! ]2 ≤ TL+F ≤ 150, 2 ≤ TR ≤ 150, 2 ≤ TF ≤ 150
[ ! ] An applicable retaining ring is included in the retaining ring groove.

(Reference Value) High Hardness Stainless Steel Center Hardness

D	Center Hardness (HRC)
3	35 or More
4	35 or More
5	35 or More
6	35 or More
8	35 or More
10	30 or More
12	30 or More
15	30 or More
16	30 or More
20	25 or More
25	25 or More

Mechanical Properties (Reference Value)

Material	Tensile Strength (Mpa)	Yielding Point (0.2% Proof Stress) (MPa)	Young's Modulus (GPa)	Transverse Modulus (GPa)	Poisson Ratio
Material	Tensile Strength (Mpa)	Yielding Point (0.2% Proof Stress) (MPa)	Young's Modulus (GPa)	Transverse Modulus (GPa)	Poisson Ratio
EN 1.1191 Equiv.	570 or More	345 or More	200 or More	77 or More	0.3
EN 1.4301 Equiv.	520 or More	210 or More	193 or More	74 or More	0.3
EN 1.7220 Equiv.	930 or More	785 or More	206 or More	79 or More	0.3
High Hardness Stainless Steel	1102	715	199	77	0.3

High Hardness Stainless Steel Material Properties
(Unit: %)

C	Si	Mn	P	S	Ni	Cr
0.15-0.25	≤ 0.50	7.5-9.5	≤ 0.05	≥ 0.12	1.5-3.0	13-15

Part Number:

3D preview is not available, because the part number has not yet been determined.

In order to open the 3D preview, the part number must be fixed.

Plug-in is required for 3D Preview

CAD Download

Data to be displayed: 30; 45; 60

Part Number
SSFRMGNS20-[30-995/0.1]-F[2-112/0.1]-B[3-67/1]-P[6,8,10,12,16]-SC[0-985/1]
SSFRMGNS20-[30-995/0.1]-F[2-112/0.1]-B[3-67/1]-PMC[6,8,10,12,15,17]-SC[0-985/1]
SSFRMGNS25-[30-995/0.1]-F[3-140/0.1]-B[3-80/1]-P20-SC[0-985/1]
SSFRMGNS25-[30-995/0.1]-F[3-140/0.1]-B[3-80/1]-PMC[8,10,12,15,17,20]-SC[0-985/1]
SSFRMGNS30-[30-995/0.1]-F[3-168/0.1]-B[3-72/1]-P20-SC[0-980/1]
SSFRMGNS30-[30-995/0.1]-F[3-168/0.1]-B[3-72/1]-PMC[8,10,12,15,17,20,25]-SC[0-980/1]
SSFRMGNS35-[40-995/0.1]-F[3-210/0.1]-B[3-90/1]-P20-SC[0-980/1]
SSFRMGNS35-[40-995/0.1]-F[3-210/0.1]-B[3-90/1]-PMC[10,12,15,17,20,25,30]-SC[0-980/1]
SSFRMHN6-[15-495/0.1]-F[2-42/0.1]-B[3-18/1]-P[3,4,5]
SSFRMHN6-[15-495/0.1]-F[2-42/0.1]-B[3-18/1]-PMC[3,4,5,6]
SSFRMHN8-[15-495/0.1]-F[2-42/0.1]-B[3-18/1]-P[3,4,5,6]
SSFRMHN8-[15-495/0.1]-F[2-42/0.1]-B[3-18/1]-PMC[3,4,5,6]
SSFRMHN10-[15-595/0.1]-F[2-56/0.1]-B[3-30/1]-P[4,5,6,8]
SSFRMHN10-[15-595/0.1]-F[2-56/0.1]-B[3-30/1]-PMC[4,5,6,8]
SSFRMHN12-[15-695/0.1]-F[2-70/0.1]-B[3-53/1]-P[5,6,8,10]
SSFRMHN12-[15-695/0.1]-F[2-70/0.1]-B[3-53/1]-PMC[5,6,8,10]
SSFRMHN15-[15-795/0.1]-F[2-84/0.1]-B[3-53/1]-P[5,6,8,10,12]
SSFRMHN15-[15-795/0.1]-F[2-84/0.1]-B[3-53/1]-PMC[5,6,8,10,12]
SSFRMHN16-[15-995/0.1]-F[2-105/0.1]-B[3-53/1]-P[4,5,6,8,10,12]
SSFRMHN16-[15-995/0.1]-F[2-105/0.1]-B[3-53/1]-PMC[5,6,8,10,12]
SSFRMHN20-[30-995/0.1]-F[2-112/0.1]-B[3-48/1]-P[6,8,10,12,16]
SSFRMHN20-[30-995/0.1]-F[2-112/0.1]-B[3-48/1]-PMC[6,8,10,12,15,17]
SSFRMHN25-[30-995/0.1]-F[3-140/0.1]-B[3-75/1]-P20
SSFRMHN25-[30-995/0.1]-F[3-140/0.1]-B[3-75/1]-PMC[8,10,12,15,17,20]
SSFRMHN30-[30-995/0.1]-F[3-168/0.1]-B[3-75/1]-P20
SSFRMHN30-[30-995/0.1]-F[3-168/0.1]-B[3-75/1]-PMC[8,10,12,15,17,20,25]
SSFRMHN35-[40-995/0.1]-F[3-210/0.1]-B[3-90/1]-P20
SSFRMHN35-[40-995/0.1]-F[3-210/0.1]-B[3-90/1]-PMC[10,12,15,17,20,25,30]
SSFRMHNS6-[15-495/0.1]-F[2-42/0.1]-B[3-18/1]-P[3,4,5]-SC[0-487/1]
SSFRMHNS6-[15-495/0.1]-F[2-42/0.1]-B[3-18/1]-PMC[3,4,5,6]-SC[0-487/1]
SSFRMHNS8-[15-495/0.1]-F[2-42/0.1]-B[3-18/1]-P[3,4,5,6]-SC[0-487/1]
SSFRMHNS8-[15-495/0.1]-F[2-42/0.1]-B[3-18/1]-PMC[3,4,5,6]-SC[0-487/1]
SSFRMHNS10-[15-595/0.1]-F[2-56/0.1]-B[3-53/1]-P[4,5,6,8]-SC[0-587/1]
SSFRMHNS10-[15-595/0.1]-F[2-56/0.1]-B[3-53/1]-PMC[4,5,6,8]-SC[0-587/1]
SSFRMHNS12-[15-695/0.1]-F[2-70/0.1]-B[3-31/1]-P[5,6,8,10]-SC[0-685/1]
SSFRMHNS12-[15-695/0.1]-F[2-70/0.1]-B[3-31/1]-PMC[5,6,8,10]-SC[0-685/1]
SSFRMHNS15-[15-795/0.1]-F[2-84/0.1]-B0-P[5,6,8,10,12]-SC[0-785/1]
SSFRMHNS15-[15-795/0.1]-F[2-84/0.1]-B0-PMC[5,6,8,10,12]-SC[0-785/1]
SSFRMHNS15-[15-795/0.1]-F[2-84/0.1]-B[3-36/1]-P[5,6,8,10,12]-SC[0-785/1]
SSFRMHNS15-[15-795/0.1]-F[2-84/0.1]-B[3-36/1]-PMC[5,6,8,10,12]-SC[0-785/1]
SSFRMHNS16-[15-995/0.1]-F[2-105/0.1]-B[3-53/1]-P[4,5,6,8,10,12]-SC[0-985/1]
SSFRMHNS16-[15-995/0.1]-F[2-105/0.1]-B[3-53/1]-PMC[5,6,8,10,12]-SC[0-985/1]
SSFRMHNS20-[30-995/0.1]-F[2-112/0.1]-B[3-67/1]-P[6,8,10,12,16]-SC[0-985/1]
SSFRMHNS20-[30-995/0.1]-F[2-112/0.1]-B[3-67/1]-PMC[6,8,10,12,15,17]-SC[0-985/1]
SSFRMHNS25-[30-995/0.1]-F[3-140/0.1]-B[3-80/1]-P20-SC[0-985/1]
SSFRMHNS25-[30-995/0.1]-F[3-140/0.1]-B[3-80/1]-PMC[8,10,12,15,17,20]-SC[0-985/1]
SSFRMHNS30-[30-995/0.1]-F[3-168/0.1]-B[3-72/1]-P20-SC[0-980/1]
SSFRMHNS30-[30-995/0.1]-F[3-168/0.1]-B[3-72/1]-PMC[8,10,12,15,17,20,25]-SC[0-980/1]
SSFRMHNS35-[40-995/0.1]-F[3-210/0.1]-B[3-90/1]-P20-SC[0-980/1]
SSFRMHNS35-[40-995/0.1]-F[3-210/0.1]-B[3-90/1]-PMC[10,12,15,17,20,25,30]-SC[0-980/1]
SSFRN6-[15-395/0.1]-F[2-35/0.1]-B[3-15/1]-P[3,4,5]
SSFRN6-[15-395/0.1]-F[2-35/0.1]-B[3-15/1]-PMC[3,4,5]
SSFRN8-[15-495/0.1]-F[2-42/0.1]-B[3-18/1]-P[3,4,5,6]
SSFRN8-[15-495/0.1]-F[2-42/0.1]-B[3-18/1]-PMC[3,4,5,6]
SSFRN10-[15-595/0.1]-F[2-56/0.1]-B[3-30/1]-P[4,5,6,8]
SSFRN10-[15-595/0.1]-F[2-56/0.1]-B[3-30/1]-PMC[4,5,6,8]
SSFRN12-[15-695/0.1]-F[2-70/0.1]-B[3-53/1]-P[5,6,8,10]
SSFRN12-[15-695/0.1]-F[2-70/0.1]-B[3-53/1]-PMC[5,6,8,10]
SSFRN13-[15-895/0.1]-F[2-84/0.1]-B[3-53/1]-P[4,5,6,8,10]
SSFRN13-[15-895/0.1]-F[2-84/0.1]-B[3-53/1]-PMC[5,6,8,10]

Standard Unit Price	Minimum order quantity	Standard Shipping Days ?	RoHS	Material	Hardness	Surface Treatment	D Tolerance	Shaft Dia. D (mm)	Length L (mm)	Wrench Flats	P Tolerance	B (mm)	P (mm)	Change to Fine Threads [PMC] (mm)	F (mm)	P (mm)	Wrench Flats Machining [SC] (mm)
-	1	4 Days	10	[Stainless Steel] EN 1.4301 Equiv.	No Hardened	NA	h9 (Cold-drawn)	20	30 ～ 995	With Wrench Flats	g6	1 ～ 67	-	-	2 ～ 112	6 ～ 16	0 ～ 985
-	1	4 Days	10	[Stainless Steel] EN 1.4301 Equiv.	No Hardened	NA	h9 (Cold-drawn)	20	30 ～ 995	With Wrench Flats	g6	1 ～ 67	-	6 ～ 17	2 ～ 112	-	0 ～ 985
-	1	4 Days	10	[Stainless Steel] EN 1.4301 Equiv.	No Hardened	NA	h9 (Cold-drawn)	25	30 ～ 995	With Wrench Flats	g6	1 ～ 80	-	-	3 ～ 140	8 ～ 20	0 ～ 985
-	1	4 Days	10	[Stainless Steel] EN 1.4301 Equiv.	No Hardened	NA	h9 (Cold-drawn)	25	30 ～ 995	With Wrench Flats	g6	1 ～ 80	-	8 ～ 20	3 ～ 140	-	0 ～ 985
-	1	4 Days	10	[Stainless Steel] EN 1.4301 Equiv.	No Hardened	NA	h9 (Cold-drawn)	30	30 ～ 995	With Wrench Flats	g6	1 ～ 72	-	-	3 ～ 168	8 ～ 24	0 ～ 980
-	1	4 Days	10	[Stainless Steel] EN 1.4301 Equiv.	No Hardened	NA	h9 (Cold-drawn)	30	30 ～ 995	With Wrench Flats	g6	1 ～ 72	-	8 ～ 25	3 ～ 168	-	0 ～ 980
-	1	9 Days	10	[Stainless Steel] EN 1.4301 Equiv.	No Hardened	NA	h9 (Cold-drawn)	35	40 ～ 995	With Wrench Flats	g6	0 ～ 90	-	-	3 ～ 210	10 ～ 30	0 ～ 980
-	1	9 Days	10	[Stainless Steel] EN 1.4301 Equiv.	No Hardened	NA	h9 (Cold-drawn)	35	40 ～ 995	With Wrench Flats	g6	0 ～ 90	-	10 ～ 30	3 ～ 210	-	0 ～ 980
-	1	9 Days	-	[Stainless Steel] EN 1.4301 Equiv.	No Hardened	NA	h9 (Cold-drawn)	6	15 ～ 495	W/o Wrench Flats	h7	0 ～ 18	-	-	2 ～ 42	3 ～ 5	-
-	1	9 Days	-	[Stainless Steel] EN 1.4301 Equiv.	No Hardened	NA	h9 (Cold-drawn)	6	15 ～ 495	W/o Wrench Flats	h7	0 ～ 18	-	3 ～ 6	2 ～ 42	-	-
-	1	4 Days	10	[Stainless Steel] EN 1.4301 Equiv.	No Hardened	NA	h9 (Cold-drawn)	8	15 ～ 495	With Wrench Flats	h7	1 ～ 18	-	-	2 ～ 42	3 ～ 6	-
-	1	4 Days	10	[Stainless Steel] EN 1.4301 Equiv.	No Hardened	NA	h9 (Cold-drawn)	8	15 ～ 495	With Wrench Flats	h7	1 ～ 18	-	3 ～ 6	2 ～ 42	-	-
-	1	4 Days	10	[Stainless Steel] EN 1.4301 Equiv.	No Hardened	NA	h9 (Cold-drawn)	10	15 ～ 595	With Wrench Flats	h7	1 ～ 30	-	-	2 ～ 56	4 ～ 8	-
-	1	4 Days	10	[Stainless Steel] EN 1.4301 Equiv.	No Hardened	NA	h9 (Cold-drawn)	10	15 ～ 595	With Wrench Flats	h7	1 ～ 30	-	4 ～ 8	2 ～ 56	-	-
-	1	4 Days	10	[Stainless Steel] EN 1.4301 Equiv.	No Hardened	NA	h9 (Cold-drawn)	12	15 ～ 695	With Wrench Flats	h7	1 ～ 53	-	-	2 ～ 70	5 ～ 10	-
-	1	4 Days	10	[Stainless Steel] EN 1.4301 Equiv.	No Hardened	NA	h9 (Cold-drawn)	12	15 ～ 695	With Wrench Flats	h7	1 ～ 53	-	5 ～ 10	2 ～ 70	-	-
-	1	4 Days	10	[Stainless Steel] EN 1.4301 Equiv.	No Hardened	NA	h9 (Cold-drawn)	15	15 ～ 795	With Wrench Flats	h7	1 ～ 53	-	-	2 ～ 84	5 ～ 12	-
-	1	4 Days	10	[Stainless Steel] EN 1.4301 Equiv.	No Hardened	NA	h9 (Cold-drawn)	15	15 ～ 795	With Wrench Flats	h7	1 ～ 53	-	5 ～ 12	2 ～ 84	-	-
-	1	9 Days	-	[Stainless Steel] EN 1.4301 Equiv.	No Hardened	NA	h9 (Cold-drawn)	16	15 ～ 995	W/o Wrench Flats	h7	0 ～ 53	-	-	2 ～ 105	4 ～ 12	-
-	1	9 Days	-	[Stainless Steel] EN 1.4301 Equiv.	No Hardened	NA	h9 (Cold-drawn)	16	15 ～ 995	W/o Wrench Flats	h7	0 ～ 53	-	5 ～ 12	2 ～ 105	-	-
-	1	4 Days	10	[Stainless Steel] EN 1.4301 Equiv.	No Hardened	NA	h9 (Cold-drawn)	20	30 ～ 995	With Wrench Flats	h7	1 ～ 48	-	-	2 ～ 112	6 ～ 16	-
-	1	4 Days	10	[Stainless Steel] EN 1.4301 Equiv.	No Hardened	NA	h9 (Cold-drawn)	20	30 ～ 995	With Wrench Flats	h7	1 ～ 48	-	6 ～ 17	2 ～ 112	-	-
-	1	4 Days	10	[Stainless Steel] EN 1.4301 Equiv.	No Hardened	NA	h9 (Cold-drawn)	25	30 ～ 995	With Wrench Flats	h7	1 ～ 75	-	-	3 ～ 140	8 ～ 20	-
-	1	4 Days	10	[Stainless Steel] EN 1.4301 Equiv.	No Hardened	NA	h9 (Cold-drawn)	25	30 ～ 995	With Wrench Flats	h7	1 ～ 75	-	8 ～ 20	3 ～ 140	-	-
-	1	4 Days	10	[Stainless Steel] EN 1.4301 Equiv.	No Hardened	NA	h9 (Cold-drawn)	30	30 ～ 995	With Wrench Flats	h7	1 ～ 75	-	-	3 ～ 168	8 ～ 24	-
-	1	4 Days	10	[Stainless Steel] EN 1.4301 Equiv.	No Hardened	NA	h9 (Cold-drawn)	30	30 ～ 995	With Wrench Flats	h7	1 ～ 75	-	8 ～ 25	3 ～ 168	-	-
-	1	9 Days	10	[Stainless Steel] EN 1.4301 Equiv.	No Hardened	NA	h9 (Cold-drawn)	35	40 ～ 995	With Wrench Flats	h7	0 ～ 90	-	-	3 ～ 210	10 ～ 30	-
-	1	9 Days	10	[Stainless Steel] EN 1.4301 Equiv.	No Hardened	NA	h9 (Cold-drawn)	35	40 ～ 995	With Wrench Flats	h7	0 ～ 90	-	10 ～ 30	3 ～ 210	-	-
-	1	9 Days	-	[Stainless Steel] EN 1.4301 Equiv.	No Hardened	NA	h9 (Cold-drawn)	6	15 ～ 495	With Wrench Flats	h7	0 ～ 18	-	-	2 ～ 42	3 ～ 5	0 ～ 487
-	1	9 Days	-	[Stainless Steel] EN 1.4301 Equiv.	No Hardened	NA	h9 (Cold-drawn)	6	15 ～ 495	With Wrench Flats	h7	0 ～ 18	-	3 ～ 6	2 ～ 42	-	0 ～ 487
-	1	4 Days	10	[Stainless Steel] EN 1.4301 Equiv.	No Hardened	NA	h9 (Cold-drawn)	8	15 ～ 495	With Wrench Flats	h7	1 ～ 18	-	-	2 ～ 42	3 ～ 6	0 ～ 487
-	1	4 Days	10	[Stainless Steel] EN 1.4301 Equiv.	No Hardened	NA	h9 (Cold-drawn)	8	15 ～ 495	With Wrench Flats	h7	1 ～ 18	-	3 ～ 6	2 ～ 42	-	0 ～ 487
-	1	4 Days	10	[Stainless Steel] EN 1.4301 Equiv.	No Hardened	NA	h9 (Cold-drawn)	10	15 ～ 595	With Wrench Flats	h7	1 ～ 53	-	-	2 ～ 56	4 ～ 8	0 ～ 587
-	1	4 Days	10	[Stainless Steel] EN 1.4301 Equiv.	No Hardened	NA	h9 (Cold-drawn)	10	15 ～ 595	With Wrench Flats	h7	1 ～ 53	-	4 ～ 8	2 ～ 56	-	0 ～ 587
-	1	4 Days	10	[Stainless Steel] EN 1.4301 Equiv.	No Hardened	NA	h9 (Cold-drawn)	12	15 ～ 695	With Wrench Flats	h7	1 ～ 31	-	-	2 ～ 70	5 ～ 10	0 ～ 685
-	1	4 Days	10	[Stainless Steel] EN 1.4301 Equiv.	No Hardened	NA	h9 (Cold-drawn)	12	15 ～ 695	With Wrench Flats	h7	1 ～ 31	-	5 ～ 10	2 ～ 70	-	0 ～ 685
-	1	4 Days	10	[Stainless Steel] EN 1.4301 Equiv.	No Hardened	NA	h9 (Cold-drawn)	15	15 ～ 795	With Wrench Flats	h7	0	-	-	2 ～ 84	5 ～ 12	0 ～ 785
-	1	4 Days	10	[Stainless Steel] EN 1.4301 Equiv.	No Hardened	NA	h9 (Cold-drawn)	15	15 ～ 795	With Wrench Flats	h7	0	-	5 ～ 12	2 ～ 84	-	0 ～ 785
-	1	4 Days	10	[Stainless Steel] EN 1.4301 Equiv.	No Hardened	NA	h9 (Cold-drawn)	15	15 ～ 795	With Wrench Flats	h7	3 ～ 36	-	-	2 ～ 84	5 ～ 12	0 ～ 785
-	1	4 Days	10	[Stainless Steel] EN 1.4301 Equiv.	No Hardened	NA	h9 (Cold-drawn)	15	15 ～ 795	With Wrench Flats	h7	3 ～ 36	-	5 ～ 12	2 ～ 84	-	0 ～ 785
-	1	9 Days	-	[Stainless Steel] EN 1.4301 Equiv.	No Hardened	NA	h9 (Cold-drawn)	16	15 ～ 995	With Wrench Flats	h7	0 ～ 53	-	-	2 ～ 105	4 ～ 12	0 ～ 985
-	1	9 Days	-	[Stainless Steel] EN 1.4301 Equiv.	No Hardened	NA	h9 (Cold-drawn)	16	15 ～ 995	With Wrench Flats	h7	0 ～ 53	-	5 ～ 12	2 ～ 105	-	0 ～ 985
-	1	4 Days	10	[Stainless Steel] EN 1.4301 Equiv.	No Hardened	NA	h9 (Cold-drawn)	20	30 ～ 995	With Wrench Flats	h7	1 ～ 67	-	-	2 ～ 112	6 ～ 16	0 ～ 985
-	1	4 Days	10	[Stainless Steel] EN 1.4301 Equiv.	No Hardened	NA	h9 (Cold-drawn)	20	30 ～ 995	With Wrench Flats	h7	1 ～ 67	-	6 ～ 17	2 ～ 112	-	0 ～ 985
-	1	4 Days	10	[Stainless Steel] EN 1.4301 Equiv.	No Hardened	NA	h9 (Cold-drawn)	25	30 ～ 995	With Wrench Flats	h7	1 ～ 80	-	-	3 ～ 140	8 ～ 20	0 ～ 985
-	1	4 Days	10	[Stainless Steel] EN 1.4301 Equiv.	No Hardened	NA	h9 (Cold-drawn)	25	30 ～ 995	With Wrench Flats	h7	1 ～ 80	-	8 ～ 20	3 ～ 140	-	0 ～ 985
-	1	4 Days	10	[Stainless Steel] EN 1.4301 Equiv.	No Hardened	NA	h9 (Cold-drawn)	30	30 ～ 995	With Wrench Flats	h7	1 ～ 72	-	-	3 ～ 168	8 ～ 24	0 ～ 980
-	1	4 Days	10	[Stainless Steel] EN 1.4301 Equiv.	No Hardened	NA	h9 (Cold-drawn)	30	30 ～ 995	With Wrench Flats	h7	1 ～ 72	-	8 ～ 25	3 ～ 168	-	0 ～ 980
-	1	9 Days	10	[Stainless Steel] EN 1.4301 Equiv.	No Hardened	NA	h9 (Cold-drawn)	35	40 ～ 995	With Wrench Flats	h7	0 ～ 90	-	-	3 ～ 210	10 ～ 30	0 ～ 980
-	1	9 Days	10	[Stainless Steel] EN 1.4301 Equiv.	No Hardened	NA	h9 (Cold-drawn)	35	40 ～ 995	With Wrench Flats	h7	0 ～ 90	-	10 ～ 30	3 ～ 210	-	0 ～ 980
-	1	4 Days	10	[Stainless Steel] EN 1.4301 Equiv.	No Hardened	NA	g6 (Ground)	6	15 ～ 395	With Wrench Flats	g6	2 ～ 15	-	-	2 ～ 35	3 ～ 5	-
-	1	4 Days	10	[Stainless Steel] EN 1.4301 Equiv.	No Hardened	NA	g6 (Ground)	6	15 ～ 395	With Wrench Flats	g6	2 ～ 15	-	3 ～ 5	2 ～ 35	-	-
-	1	4 Days	10	[Stainless Steel] EN 1.4301 Equiv.	No Hardened	NA	g6 (Ground)	8	15 ～ 495	With Wrench Flats	g6	2 ～ 18	-	-	2 ～ 42	3 ～ 6	-
-	1	4 Days	10	[Stainless Steel] EN 1.4301 Equiv.	No Hardened	NA	g6 (Ground)	8	15 ～ 495	With Wrench Flats	g6	2 ～ 18	-	3 ～ 6	2 ～ 42	-	-
-	1	4 Days	10	[Stainless Steel] EN 1.4301 Equiv.	No Hardened	NA	g6 (Ground)	10	15 ～ 595	With Wrench Flats	g6	2 ～ 30	-	-	2 ～ 56	4 ～ 8	-
-	1	4 Days	10	[Stainless Steel] EN 1.4301 Equiv.	No Hardened	NA	g6 (Ground)	10	15 ～ 595	With Wrench Flats	g6	2 ～ 30	-	4 ～ 8	2 ～ 56	-	-
-	1	4 Days	10	[Stainless Steel] EN 1.4301 Equiv.	No Hardened	NA	g6 (Ground)	12	15 ～ 695	With Wrench Flats	g6	2 ～ 53	-	-	2 ～ 70	5 ～ 10	-
-	1	4 Days	10	[Stainless Steel] EN 1.4301 Equiv.	No Hardened	NA	g6 (Ground)	12	15 ～ 695	With Wrench Flats	g6	2 ～ 53	-	5 ～ 10	2 ～ 70	-	-
-	1	9 Days	-	[Stainless Steel] EN 1.4301 Equiv.	No Hardened	NA	g6 (Ground)	13	15 ～ 895	W/o Wrench Flats	g6	0 ～ 53	-	-	2 ～ 84	4 ～ 10	-
-	1	9 Days	-	[Stainless Steel] EN 1.4301 Equiv.	No Hardened	NA	g6 (Ground)	13	15 ～ 895	W/o Wrench Flats	g6	0 ～ 53	-	5 ～ 10	2 ～ 84	-	-

App. Example

Rotary Shaft - One End Stepped, One End Threaded: Related Image

Products homepage

Basic information

Basic Shape	One End Stepped	Environmentally friendly	RoHS Compliant (10 Substances)	End Shape (Left)	Threads
Characteristics/Applications	Not Applicable	End Shape (Right)	Straight	Keyway	Keyway Option (Alteration)
Cleaning Method	No Cleaning

Configure

956Suggestion of an applicable part number.

View Part Numbers

Some specification is not specified yet.

The part number is completed.

Basic Attributes

Material
- Steel
  - EN 1.1191 Equiv.
  - EN 1.7220 Equiv.
- Stainless Steel
  - EN 1.4301 Equiv.
  - Stainless Steel, austenitic (high hardness: 35 HRC or More)
Clear
Hardness
- No Hardened
- Hardened
Clear
Surface Treatment
- NA
- Surface Treatment Provided
  - Black Oxide
  - Electroless Nickel Plating
Clear
D Tolerance
- h9 (Cold-drawn)
- h7 (Ground)
- g6 (Ground)
Clear
Shaft Dia. D(mm)
6

8

10

12

13

15

16

17

18

20

22

25

30

35

40

50
Clear
Length L(mm)
[15-995/0.1mm Unit(s)]
Clear
Wrench Flats
- W/o Wrench Flats
- With Wrench Flats
Clear
P Tolerance
- g6
- h7
Clear
B(mm)
0

2
[3-90/1mm Unit(s)]
Clear
P(mm)
20
Clear
Change to Fine Threads [PMC](mm)
3

4

5

6

8

10

12

15

17

20

25

30

35

40
Clear
F(mm)
[2-210/0.1mm Unit(s)]
Clear
P(mm)
3

4

5

6

8

10

12

16

20

24

30
Clear
Wrench Flats Machining [SC](mm)
[0-985/1mm Unit(s)]
Clear
Type
- AHFRN
- AHFRNS
- HFRN
- HFRNS
- NSFRHN
- NSFRHNS
- NSFRMGN
- NSFRMGNS
- NSFRMHN
- NSFRMHNS
- NSFRN
- NSFRNS
- PHFRN
- PSFRHN
- PSFRHNS
- PSFRMGN
- PSFRMGNS
- PSFRMHN
- PSFRMHNS
- PSFRN
- PSFRNS
- SFRHN
- SFRHNS
- SFRMGN
- SFRMGNS
- SFRMHN
- SFRMHNS
- SFRN
- SFRNS
- SSFRHN
- SSFRHNS
- SSFRMGN
- SSFRMGNS
- SSFRMHN
- SSFRMHNS
- SSFRN
- SSFRNS
Clear
Filter by CAD data type
- 2D
- 3D
Clear