Szűrési feltételek
  • Készlet
  • [dr] Inner Diameter(mm)
  • [L] Length (Total)(mm)
  • Outer Cylinder Surface Treatment
    • Surface Treatment
  • [D] Outer Diameter(mm)
  • Eccentricity(μm)
  • CAD
  • Becsült szállítási napok
    • Minden
    • Aznapi feladás lehetséges
    • 5 munkanapok belül
    • 9 munkanapok belül
    • 11 munkanapok belül
    • 12 munkanapok belül
    • 13 munkanapok belül
    • 15 munkanapok belül
    • 17 munkanapok belül
  • Linear ball bearings / flange selectable / steel / double bush / lubricating

    Cikkszám:

    Befejezetlen: 54 javaslat található.
    Mennyiség:

    Vázlatrajz és specifikációs táblázat

    Back to the Category Linear Ball Bushings

    Technical Drawing - Linear Ball Bushings

     

    Flanged Linear Bushing/Double Bushing/With Lubrication Unit MX:Related Image

     

    Basic Properties (e.g., material, hardness, coating, tolerance) - Linear Ball Bushings
     
    TypeOuter CylinderBallsPad Case / RetainerAmbient Operating Temp. Accessory
    Round FlangedSquare FlangedCompact Flanged Material Hardness Surface Treatment Material Material
    LHFRW-MXLHFSW-MXLHFCW-MXEN 1.3505 Equiv.58HRC~-EN 1.3505 Equiv.Plastic
    (Duracon M90 Equiv.)
    -20~80°CSealMaterial
    Nitrile Rubber
    LHFRWM-MXLHFSWM-MXLHFCWM-MXElectroless Nickel PlatingEN 1.4125 Equiv.

     

    Further specifications can be found under the tab More Information.

    Details on lubricants can be found in the catalog on p. 304

     

    Composition of a Product Code - Linear Ball Bushings

     

    Part Number 
    LHFRW-MX16
    LHMSW-MX20
    Various Grease Application Services are not applicable.

     

    General Information - Linear Ball Bushings

     

    Linear Ball Bushing Selection Details

    - Inner diameter [dr]: 3 mm – 100 mm
    - Total length [L]: 10 mm – 300 mm
    - Housing material: aluminum, stainless steel (stainless steel), steel
    - Ball material: stainless steel (stainless steel), steel
    - Ball cage material: plastic, stainless steel (stainless steel)
    - Surface treatment: without, chemically nickel-plated, LTBC
    - Radial offset (μm): 50 μm – 4 μm

    At MISUMI, you will find the following linear bearing versions: with locking ring with groove, with dust seal, with lubrication unit (MX), with grease nipple, housing open at the bottom/open, with clearance compensation, with flange, with centred flange, with round flange, with flattened round flange (compact flange), with square flange, with block housing, with wide barrel and ball housing, ball cage guides for linear and rotational movements (limited stroke).

     

    Description/Basics

    Linear ball bushings convert the rolling motion of steel balls (4) into infinite linear motion. They can implement highly precise and low-friction linear motion and can be used in almost all industries, e.g., in systems for semiconductor parts, electronic components and in food packaging.

    Ball recirculating bushings are used in conjunction with linear shafts. The linear movement mechanism uses steel balls (4) for unlimited linear movement.

    Linear bearing units allow linear shafts to travel indefinitely through steel balls that are constantly circulating within the running grooves directed by the outer cylinder and ball cage (3).

    Compared to plain bearings, ball bushings perform linear movements with lower friction and high accuracy. They are used in many applications, such as conveyors and semiconductor manufacturing facilities.

     

    Linear ball bearings - linear bearings - recirculating ball bushing - recirculating ball bushings - linear bearing unit - linear bearing units - ball bushing - ball bushings

     

    Linear Bearing Unit Design - (1) Dust Seal, (2) Outer Cylinder, (3) Ball Cage, (4) Steel Balls

     

    Dynamic friction coefficient in comparison

    DesignDynamic friction coefficient (μ)
    Miniature profile rail guide0.004 ~ 0.006
    Profile rail guide for medium and heavy loads0.002 ~ 0.003
    Cross roller guides0.001 ~ 0.003
    Cross roller tables0.001 ~ 0.003
    Linear ball bearing0.002 ~ 0.003
    Ball cage guides0.0006 ~ 0.0012

    The specified values are for comparison purposes only and are therefore not reference values.

     

    Areas of Application

    Linear ball bushings have a linear working direction and can be used for horizontal or vertical linear movements. Therefore, MISUMI linear ball bushings can be used in almost all industries. Since linear ball bushings are intended only for axial movement, rotational use would lead to premature fatigue or destruction of the ball bushings. For rotary movements, we therefore recommend ball cage guides, which enable not only infinite linear movements (stroke-limited) in addition to infinite rotary movements.

    Common applications are lifting mechanisms or guides for cylinders. The ball bushings are also a good variant for additional guide. In addition, these linear ball bushings are often found in 3D printers, metering systems, measuring devices, positioning and alignment devices, bending devices and sorting systems.

    For systems with increased particle development (e.g., dust and other abrasive particles), the linear systems should be protected with covers or bellows. The ingress of particles leads to a clumping of the lubricating grease or to significantly increased abrasion. By clumping the grease, the balls block in the ball circulation, which results in unscheduled maintenance.

     

    Linear ball bearings - linear bearings - recirculating ball bushing - recirculating ball bushings - linear bearing unit - linear bearing units - ball bushing - ball bushings
    Linear ball bearings - linear bearings - recirculating ball bushing - recirculating ball bushings - linear bearing unit - linear bearing units - ball bushing - ball bushings

      

    Materials

    Linear ball bearings consist of different materials due to their design and the individual components. MISUMI uses high-quality materials to achieve the longest possible service life. The following materials are available:

    - External cylinder: stainless steel (stainless steel) ~56HRC, steel with ~58HRC
    - Ball: stainless steel (stainless steel), steel
    - Ball cage: plastic, stainless steel (stainless steel)
    - Housing: aluminum, stainless steel (stainless steel), steel
    - Seal: nitrile rubber

    You can find more detailed material information in the tab Technical Drawing.

     

    Coatings

    To protect linear ball bushings from corrosion, the surface can be chemically nickel-plated.

    As an alternative to a chemical nickel-plating, ball bushings can also be coated with LTBC. The LTBC coating (Low Temperature Black Chrome Platinum) is a surface treatment that protects against corrosion and has low reflection. The coating consists of a 5 μm thick chrome ceramic layer with fluoropolymer infusion and it deposits as a black film. In addition, the LTBC coating is crack-proof and interchangeable and is therefore resistant to delamination due to extreme or repeated bending. LTBC-coated linear ball bearings are thus particularly suitable for locations where corrosion or light reflections are undesirable.

    Note: the inner wall of LTBC coated linear bushing units is not surface treated.

     

    Linear ball bearings - linear bearings - recirculating ball bushing - recirculating ball bushings - linear bearing unit - linear bearing units - ball bushing - ball bushings

    LTBC-coated linear ball bushing - state after 50 km glide test under 412N load.

     

    Comparison test of corrosion protection

     

    Linear ball bearings - linear bearings - recirculating ball bushing - recirculating ball bushings - linear bearing unit - linear bearing units - ball bushing - ball bushings

    Salt water spray test according to JIS H8502. Test piece: simple flanged linear ball bushing
    (1) EN 1.3505 equiv., (2) EN 1.4125 equiv., (3) chemically nickel-plated, (4) LTBC coating, (hr = duration in hours)

     

    Instructions for Use / Installation Information - Linear Ball Bushings

     

    Instructions for use

    - MISUMI linear bearings should be used in conjunction with MISUMI linear shafts.
    - We recommend using a hardened linear shaft in the g6 tolerance.
    - An additional hard chrome plating of the linear shaft makes it more wear-resistant.
    - When installing ball bushings in housings, we recommend an H7 housing tolerance. Too close a tolerance will reduce the internal contact travel [dr] to the shaft and can lead to increased wear and premature failure.
    - The utilisation of two ball bushings on a steel shaft improves the shaft guide in a system. However, if the angular errors are too high, a self-aligning linear ball bushing should be selected.
    - When utilising two linear shafts, the drive should be centred in the system to avoid unnecessary stresses/lever effects.
    - The service life, also called nominal service life, should be calculated using the present load case. Here you can perform your service life calculation.
    - Depending on local conditions such as temperature, humidity and gases, a variant made of stainless steel or an LTBC coating is recommended.
    - When the linear shafts bend sharply, a self-aligning/self-adjusting linear ball bushing should be selected.

     

    Installation Information

    General installation instructions for linear ball bushings and linear shafts

    MISUMI linear ball bushings should be used in conjunction with MISUMI linear shafts (hardened, tolerance g6).

     

    Linear ball bearings - linear bearings - recirculating ball bushing - recirculating ball bushings - linear bearing unit - linear bearing units - ball bushing - ball bushings

     

    Linear ball bearings - linear bearings - recirculating ball bushing - recirculating ball bushings - linear bearing unit - linear bearing units - ball bushing - ball bushings

    MISUMI tolerance range: inner diameter linear ball bushings (LMU) and outer diameter linear shafts (SFJ).

     

    General installation instructions for linear ball bushings and housings

    MISUMI linear ball bushings should be used in conjunction with MISUMI housings (tolerance H7).

     

    Linear ball bearings - linear bearings - recirculating ball bushing - recirculating ball bushings - linear bearing unit - linear bearing units - ball bushing - ball bushings

     

    Linear ball bearings - linear bearings - recirculating ball bushing - recirculating ball bushings - linear bearing unit - linear bearing units - ball bushing - ball bushings

    MISUMI tolerance range: outer diameter of linear ball bushing and inner diameter of housing.

     

    Standard linear ball bushing installation instructions

    1. When installing standard linear ball bushings, you can use the following locking means: retaining rings (clamping rings), stoppers

     

    Linear ball bearings - linear bearings - recirculating ball bushing - recirculating ball bushings - linear bearing unit - linear bearing units - ball bushing - ball bushings

    (1) retaining rings, (2) housing, (3) stopper/LMST fixing plate

     

    2. Ball bushings are not suitable for rotary motion and applications requiring repetitive insertion and removal of linear shafts. Such a misuse of the linear ball bushing could damage the recirculating ball bushing.

     

    Linear ball bearings - linear bearings - recirculating ball bushing - recirculating ball bushings - linear bearing unit - linear bearing units - ball bushing - ball bushings

     

    3. Simple linear ball bushings are not suitable for large torque loads (offset load/lever effect). The use of double or multiple linear bushings is recommended for these load cases.

     

    Linear ball bearings - linear bearings - recirculating ball bushing - recirculating ball bushings - linear bearing unit - linear bearing units - ball bushing - ball bushings

    (1) Linear ball bushing with two grooves

     

    4. When assembling linear shafts, forceful slanted insertion into the linear ball bushing can cause the ball cage to bend and the balls to fall out. Be sure to centre the steel shaft to the linear ball bushing before inserting the steel shaft into the linear ball bushing.

     

    Linear ball bearings - linear bearings - recirculating ball bushing - recirculating ball bushings - linear bearing unit - linear bearing units - ball bushing - ball bushings

     

    Installation instructions for linear ball bushings with stopper/fixing plate

    Through the stopper plates, the versions can be designed independently of the housing length.

     

    Linear ball bearings - linear bearings - recirculating ball bushing - recirculating ball bushings - linear bearing unit - linear bearing units - ball bushing - ball bushings

    (1) Attachment, (2) linear ball bushing – standard, (3) linear shaft, (4) LMST fixing plate

     

    The stopper plates enable the ball sleeve and linear shaft to be installed flush against the end faces.

     

    Linear ball bearings - linear bearings - recirculating ball bushing - recirculating ball bushings - linear bearing unit - linear bearing units - ball bushing - ball bushings

    (1) Linear shaft, (2) housing, (3) linear ball bushing – standard, (4) spacer sleeve LBS/LBSA for linear ball bushings, (5) LMST fixing plate

     

    The LMST fixing plates can also be used to lock linear bushings in place.

     

    Linear ball bearings - linear bearings - recirculating ball bushing - recirculating ball bushings - linear bearing unit - linear bearing units - ball bushing - ball bushings

    (2) housing, (4) LMST fixing plate

     

    Assembly Instructions for Linear Ball Bushings with Flange and Lubrication Unit MX

    When fastening the linear ball bushing with the lubrication unit MX, do not insert the housing of the lubrication unit as guide as shown in (2), as this can damage the housing. Instead, use the flange and guide version as shown in (3).

    Do not disassemble the linear ball bushing with flange and lubrication unit MX, as this will impair function.

     

    Linear ball bearings - linear bearings - recirculating ball bushing - recirculating ball bushings - linear bearing unit - linear bearing units - ball bushing - ball bushings

     

    Assembly Instructions for Linear Ball Bushings with Housing and without Cylinder Pin Hole

    During interface assembly, centring on the lateral reference surface can be eliminated by means of the cylinder pin holes.

    This reduces the machining effort of the upper plate to be mounted on the block.

     

    Linear ball bearings - linear bearings - recirculating ball bushing - recirculating ball bushings - linear bearing unit - linear bearing units - ball bushing - ball bushings
    Linear ball bushing with housing
    Positioning with plate end cover
    Linear ball bearings - linear bearings - recirculating ball bushing - recirculating ball bushings - linear bearing unit - linear bearing units - ball bushing - ball bushings
    Linear ball bushing with housing
    Positioning with cylinder pins

      

    Linear ball bearings - linear bearings - recirculating ball bushing - recirculating ball bushings - linear bearing unit - linear bearing units - ball bushing - ball bushings
    Linear ball bushing with housing (wide version)
    Positioning with plate end cover
    Linear ball bearings - linear bearings - recirculating ball bushing - recirculating ball bushings - linear bearing unit - linear bearing units - ball bushing - ball bushings
    Linear ball bushing with housing (wide version)
    Positioning with cylinder pins

      

      

    Maintenance - Linear Ball Bushings

     

    General Maintenance Instructions

    Grease the rows of balls inside the ball bushing before use. Then grease regularly during use. Grease reduces friction by forming a layer between the balls and rolling shaft surfaces and prevents seizing. Loss of grease and degradation of grease shorten the service life of linear guides.

    - Recommended grease: lithium soap grease
    - Recommended lubrication interval: every 6 months
    *Every 3 months for extended work or every 1000 km. Maintenance intervals vary depending on the application and ambient conditions.

     

    Lubrication

    Linear ball bushings from MISUMI are delivered coated with a corrosion protection oil. Exceptions to this are the designs with lubrication unit MX. After removing the anti-corrosion oil, we recommend lubricating the bearings.

    If you select one of the following lubricants in the configurator, you can order pre-lubricated versions. The versions L, G and H are prefilled with grease, whereby L and G offer a strong reduction in particle formation by means of a suitable grease distribution during operation (see quantitative comparison of particle formation below). Lubrication units MX are filled with lithium soap grease.

    Linear ball bearings - linear bearings - recirculating ball bushing - recirculating ball bushings - linear bearing unit - linear bearing units - ball bushing - ball bushings

    Linear ball bearings - linear bearings - recirculating ball bushing - recirculating ball bushings - linear bearing unit - linear bearing units - ball bushing - ball bushings

     

    Assembly of the lubrication unit MX

    The lubrication unit MX is equipped with a fibre insert with lubricant. The capillary effect allows the lubricant to be properly applied to contact surfaces. For this purpose, a constant oil film is formed between balls and steel shaft, which significantly prolongs the lubrication intervals.

     

    Linear ball bearings - linear bearings - recirculating ball bushing - recirculating ball bushings - linear bearing unit - linear bearing units - ball bushing - ball bushings

    Recirculation ball bushing with lubrication unit - (1) MX Lubrication Unit, (2) MX Lubrication Unit - Plastic Housing, (3) Lubricant Pads, (4) Dust Seal, (5) Balls, (6) Linear Shaft

     

    Properties of the MX lubrication unit

    Longer maintenance intervals: the long-lasting lubricant performance leads to a significant reduction in maintenance, especially in machine and equipment environments where lubrication is difficult to achieve.
    Environment: the MX lubrication unit helps reduce lubricant consumption and thus protects the environment.
    Cost benefit: it contributes to reducing maintenance costs and failure rate caused by failing to lubricate.
    Less effort: it is not necessary to refill the lubricant prior to use, since the ball parts are already filled with a lithium soap-based grease in addition to the lubrication unit.

     

    Comparison test of linear ball bearings and linear ball bearings with lubrication unit

    Test conditions:
    - Sample:
    linear ball bushing LMU12 with rust protection oil and linear ball bushing with lubrication unit LMU-MX12
    - Effective load: 206N (50% of the dynamic load rating of 412N)
    - Average speed: 42 m/min (0.7 m/s)
    - Stroke: 100 m
    - Lubricant: lubricating grease, only initial filling (only LMU-MX12)
    - Shaft material: EN 1.3505 Equiv. (58HRC)
    - Duration: 24-hour continuous operation
    *The above test conditions serve only as reference values and cannot be considered as a manufacturer warranty.

     

    Test result:

    With an effective test load of 50% of the load-carrying capacity of 412N, the design with the MX lubrication unit could achieve a continuous output of 2.5-fold longer than with no MX lubrication unit.
    *Since the 2007 catalogue, the data have been updated after the safety limit has been confirmed by further data from test results.

     

    Linearkugellager - Linearlager - Kugelumlaufbuchse - Kugelumlaufbuchsen - Linearlagereinheit - Linearlagereinheiten - Kugelbuchse - Kugelbuchsen

    Endurance test result - standard linear ball bearing LMU, linear ball bearing LMU-MX with lubricant unit

     

    Supplementary Article

     

    Linear Shaft

    Linearkugellager - Linearlager - Kugelumlaufbuchse - Kugelumlaufbuchsen - Linearlagereinheit - Linearlagereinheiten - Kugelbuchse - Kugelbuchsen

     

    Retaining Ring

    Linearkugellager - Linearlager - Kugelumlaufbuchse - Kugelumlaufbuchsen - Linearlagereinheit - Linearlagereinheiten - Kugelbuchse - Kugelbuchsen

     

    Set Collar / Clamping Ring

    Linearkugellager - Linearlager - Kugelumlaufbuchse - Kugelumlaufbuchsen - Linearlagereinheit - Linearlagereinheiten - Kugelbuchse - Kugelbuchsen

     

    Accessories for Linear Ball Bearing

    Linearkugellager - Linearlager - Kugelumlaufbuchse - Kugelumlaufbuchsen - Linearlagereinheit - Linearlagereinheiten - Kugelbuchse - Kugelbuchsen

     

    Shaft Holder

    Linearkugellager - Linearlager - Kugelumlaufbuchse - Kugelumlaufbuchsen - Linearlagereinheit - Linearlagereinheiten - Kugelbuchse - Kugelbuchsen

     

    Industrial Applications
    3D printer industry
    Linearkugellager - Linearlager - Kugelumlaufbuchse - Kugelumlaufbuchsen - Linearlagereinheit - Linearlagereinheiten - Kugelbuchse - Kugelbuchsen
    Automotive industry
    Linearkugellager - Linearlager - Kugelumlaufbuchse - Kugelumlaufbuchsen - Linearlagereinheit - Linearlagereinheiten - Kugelbuchse - Kugelbuchsen
    Pharmaceutical industry
    Linearkugellager - Linearlager - Kugelumlaufbuchse - Kugelumlaufbuchsen - Linearlagereinheit - Linearlagereinheiten - Kugelbuchse - Kugelbuchsen
    Packaging industry
    Linearkugellager - Linearlager - Kugelumlaufbuchse - Kugelumlaufbuchsen - Linearlagereinheit - Linearlagereinheiten - Kugelbuchse - Kugelbuchsen

    Cikkszámlista

    Elemek száma

    [dr] Inner Diameter

    (mm)

    [L] Length (Total)

    (mm)

    Outer Cylinder Surface Treatment

    [D] Outer Diameter

    (mm)

    Basic Load Rating Dynamic Rating (Detail)

    (N)

    Basic Load Rating Static Rating

    (N)

    Inscribed Circle Diameter Tolerance (Negative Side)

    (mm)

    Eccentricity

    (μm)

    Flange Shape

    Ball Material

    RoHS?Minimális rendelési mennyiség
    10
    64.5
    No Surface Treatment
    19
    588
    1100
    -0.01
    15
    Compact Flanged
    EN 1.3505 Equiv.
    10
    1 darab
    12
    67.3
    No Surface Treatment
    21
    657
    1200
    -0.01
    15
    Compact Flanged
    EN 1.3505 Equiv.
    10
    1 darab
    16
    82
    No Surface Treatment
    28
    1230
    2350
    -0.01
    15
    Compact Flanged
    EN 1.3505 Equiv.
    10
    10 darab
    20
    93
    No Surface Treatment
    32
    1400
    2740
    -0.012
    20
    Compact Flanged
    EN 1.3505 Equiv.
    10
    1 darab
    25
    130
    No Surface Treatment
    40
    1560
    3140
    -0.012
    20
    Compact Flanged
    EN 1.3505 Equiv.
    10
    1 darab
    30
    142
    No Surface Treatment
    45
    2490
    5490
    -0.012
    20
    Compact Flanged
    EN 1.3505 Equiv.
    10
    1 darab
    35
    155.5
    No Surface Treatment
    52
    2650
    6270
    -0.015
    25
    Compact Flanged
    EN 1.3505 Equiv.
    10
    1 darab
    40
    175
    No Surface Treatment
    60
    3430
    8040
    -0.015
    25
    Compact Flanged
    EN 1.3505 Equiv.
    10
    1 darab
    50
    220
    No Surface Treatment
    80
    6080
    15900
    -0.015
    25
    Compact Flanged
    EN 1.3505 Equiv.
    10
    1 darab
    10
    64.5
    [Surface Treatment] Electroless Nickel Plating
    19
    588
    1100
    -0.01
    15
    Compact Flanged
    EN 1.4125 Equiv.
    10
    1 darab
    12
    67.3
    [Surface Treatment] Electroless Nickel Plating
    21
    657
    1200
    -0.01
    15
    Compact Flanged
    EN 1.4125 Equiv.
    10
    1 darab
    16
    82
    [Surface Treatment] Electroless Nickel Plating
    28
    1230
    2350
    -0.01
    15
    Compact Flanged
    EN 1.4125 Equiv.
    10
    1 darab
    20
    93
    [Surface Treatment] Electroless Nickel Plating
    32
    1400
    2740
    -0.012
    20
    Compact Flanged
    EN 1.4125 Equiv.
    10
    1 darab
    25
    130
    [Surface Treatment] Electroless Nickel Plating
    40
    1560
    3140
    -0.012
    20
    Compact Flanged
    EN 1.4125 Equiv.
    10
    10 darab
    30
    142
    [Surface Treatment] Electroless Nickel Plating
    45
    2490
    5490
    -0.012
    20
    Compact Flanged
    EN 1.4125 Equiv.
    10
    10 darab
    35
    155.5
    [Surface Treatment] Electroless Nickel Plating
    52
    2650
    6270
    -0.015
    25
    Compact Flanged
    EN 1.4125 Equiv.
    10
    1 darab
    40
    175
    [Surface Treatment] Electroless Nickel Plating
    60
    3430
    8040
    -0.015
    25
    Compact Flanged
    EN 1.4125 Equiv.
    10
    1 darab
    50
    220
    [Surface Treatment] Electroless Nickel Plating
    80
    6080
    15900
    -0.015
    25
    Compact Flanged
    EN 1.4125 Equiv.
    10
    1 darab
    10
    64.5
    No Surface Treatment
    19
    588
    1100
    -0.01
    15
    Round Flanged
    EN 1.3505 Equiv.
    10
    1 darab
    12
    67.3
    No Surface Treatment
    21
    657
    1200
    -0.01
    15
    Round Flanged
    EN 1.3505 Equiv.
    10
    1 darab
    16
    82
    No Surface Treatment
    28
    1230
    2350
    -0.01
    15
    Round Flanged
    EN 1.3505 Equiv.
    10
    1 darab
    20
    93
    No Surface Treatment
    32
    1400
    2740
    -0.012
    20
    Round Flanged
    EN 1.3505 Equiv.
    10
    1 darab
    25
    130
    No Surface Treatment
    40
    1560
    3140
    -0.012
    20
    Round Flanged
    EN 1.3505 Equiv.
    10
    1 darab
    30
    142
    No Surface Treatment
    45
    2490
    5490
    -0.012
    20
    Round Flanged
    EN 1.3505 Equiv.
    10
    1 darab
    35
    155.5
    No Surface Treatment
    52
    2650
    6270
    -0.015
    25
    Round Flanged
    EN 1.3505 Equiv.
    10
    1 darab
    40
    175
    No Surface Treatment
    60
    3430
    8040
    -0.015
    25
    Round Flanged
    EN 1.3505 Equiv.
    10
    1 darab
    50
    220
    No Surface Treatment
    80
    6080
    15900
    -0.015
    25
    Round Flanged
    EN 1.3505 Equiv.
    10
    1 darab
    10
    64.5
    [Surface Treatment] Electroless Nickel Plating
    19
    588
    1100
    -0.01
    15
    Round Flanged
    EN 1.4125 Equiv.
    10
    1 darab
    12
    67.3
    [Surface Treatment] Electroless Nickel Plating
    21
    657
    1200
    -0.01
    15
    Round Flanged
    EN 1.4125 Equiv.
    10
    1 darab
    16
    82
    [Surface Treatment] Electroless Nickel Plating
    28
    1230
    2350
    -0.01
    15
    Round Flanged
    EN 1.4125 Equiv.
    10
    1 darab
    20
    93
    [Surface Treatment] Electroless Nickel Plating
    32
    1400
    2740
    -0.012
    20
    Round Flanged
    EN 1.4125 Equiv.
    10
    1 darab
    25
    130
    [Surface Treatment] Electroless Nickel Plating
    40
    1560
    3140
    -0.012
    20
    Round Flanged
    EN 1.4125 Equiv.
    10
    1 darab
    30
    142
    [Surface Treatment] Electroless Nickel Plating
    45
    2490
    5490
    -0.012
    20
    Round Flanged
    EN 1.4125 Equiv.
    10
    1 darab
    35
    155.5
    [Surface Treatment] Electroless Nickel Plating
    52
    2650
    6270
    -0.015
    25
    Round Flanged
    EN 1.4125 Equiv.
    10
    1 darab
    40
    175
    [Surface Treatment] Electroless Nickel Plating
    60
    3430
    8040
    -0.015
    25
    Round Flanged
    EN 1.4125 Equiv.
    10
    1 darab
    50
    220
    [Surface Treatment] Electroless Nickel Plating
    80
    6080
    15900
    -0.015
    25
    Round Flanged
    EN 1.4125 Equiv.
    10
    1 darab
    10
    64.5
    No Surface Treatment
    19
    588
    1100
    -0.01
    15
    Square Flanged
    EN 1.3505 Equiv.
    10
    1 darab
    12
    67.3
    No Surface Treatment
    21
    657
    1200
    -0.01
    15
    Square Flanged
    EN 1.3505 Equiv.
    10
    1 darab
    16
    82
    No Surface Treatment
    28
    1230
    2350
    -0.01
    15
    Square Flanged
    EN 1.3505 Equiv.
    10
    1 darab
    20
    93
    No Surface Treatment
    32
    1400
    2740
    -0.012
    20
    Square Flanged
    EN 1.3505 Equiv.
    10
    1 darab
    25
    130
    No Surface Treatment
    40
    1560
    3140
    -0.012
    20
    Square Flanged
    EN 1.3505 Equiv.
    10
    1 darab
    30
    142
    No Surface Treatment
    45
    2490
    5490
    -0.012
    20
    Square Flanged
    EN 1.3505 Equiv.
    10
    10 darab
    35
    155.5
    No Surface Treatment
    52
    2650
    6270
    -0.015
    25
    Square Flanged
    EN 1.3505 Equiv.
    10
    1 darab
    40
    175
    No Surface Treatment
    60
    3430
    8040
    -0.015
    25
    Square Flanged
    EN 1.3505 Equiv.
    10
    1 darab
    50
    220
    No Surface Treatment
    80
    6080
    15900
    -0.015
    25
    Square Flanged
    EN 1.3505 Equiv.
    10
    1 darab
    10
    64.5
    [Surface Treatment] Electroless Nickel Plating
    19
    588
    1100
    -0.01
    15
    Square Flanged
    EN 1.4125 Equiv.
    10
    1 darab
    12
    67.3
    [Surface Treatment] Electroless Nickel Plating
    21
    657
    1200
    -0.01
    15
    Square Flanged
    EN 1.4125 Equiv.
    10
    1 darab
    16
    82
    [Surface Treatment] Electroless Nickel Plating
    28
    1230
    2350
    -0.01
    15
    Square Flanged
    EN 1.4125 Equiv.
    10
    1 darab
    20
    93
    [Surface Treatment] Electroless Nickel Plating
    32
    1400
    2740
    -0.012
    20
    Square Flanged
    EN 1.4125 Equiv.
    10
    1 darab
    25
    130
    [Surface Treatment] Electroless Nickel Plating
    40
    1560
    3140
    -0.012
    20
    Square Flanged
    EN 1.4125 Equiv.
    10
    1 darab
    30
    142
    [Surface Treatment] Electroless Nickel Plating
    45
    2490
    5490
    -0.012
    20
    Square Flanged
    EN 1.4125 Equiv.
    10
    1 darab
    35
    155.5
    [Surface Treatment] Electroless Nickel Plating
    52
    2650
    6270
    -0.015
    25
    Square Flanged
    EN 1.4125 Equiv.
    10
    1 darab
    40
    175
    [Surface Treatment] Electroless Nickel Plating
    60
    3430
    8040
    -0.015
    25
    Square Flanged
    EN 1.4125 Equiv.
    10
    1 darab
    50
    220
    [Surface Treatment] Electroless Nickel Plating
    80
    6080
    15900
    -0.015
    25
    Square Flanged
    EN 1.4125 Equiv.
    10
    1 darab
    Egységár (HÉA nélkül)(egységár adóval)
    Normál feladási dátum
    14.80 €
    ( 17.61 € )
    Raktári cikk - 1 munkanapAznapi kiszállítással elérhető
    15.60 €
    ( 18.56 € )
    Raktári cikk - 1 munkanapAznapi kiszállítással elérhető
    17.42 €
    ( 20.73 € )
    Raktári cikk - 1 munkanapAznapi kiszállítással elérhető
    23.80 €
    ( 28.32 € )
    Raktári cikk - 1 munkanapAznapi kiszállítással elérhető
    34.05 €
    ( 40.52 € )
    11 munkanapok
    46.92 €
    ( 55.83 € )
    Raktári cikk - 1 munkanapAznapi kiszállítással elérhető
    81.89 €
    ( 97.45 € )
    5 munkanapok
    104.55 €
    ( 124.41 € )
    5 munkanapok
    139.95 €
    ( 166.54 € )
    5 munkanapok
    19.24 €
    ( 22.90 € )
    5 munkanapok
    20.38 €
    ( 24.25 € )
    Raktári cikk - 1 munkanapAznapi kiszállítással elérhető
    25.63 €
    ( 30.50 € )
    Raktári cikk - 1 munkanapAznapi kiszállítással elérhető
    30.87 €
    ( 36.74 € )
    Raktári cikk - 1 munkanapAznapi kiszállítással elérhető
    39.68 €
    ( 47.22 € )
    11 munkanapok
    54.74 €
    ( 65.14 € )
    9 munkanapok
    95.08 €
    ( 113.15 € )
    5 munkanapok
    123.66 €
    ( 147.16 € )
    5 munkanapok
    175.59 €
    ( 208.95 € )
    5 munkanapok
    14.46 €
    ( 17.21 € )
    5 munkanapok
    15.38 €9.69 €
    ( 11.53 € )
    Raktári cikk - 1 munkanapAznapi kiszállítással elérhető
    19.48 €
    ( 23.18 € )
    13 munkanapok
    23.68 €
    ( 28.18 € )
    Raktári cikk - 1 munkanapAznapi kiszállítással elérhető
    33.94 €
    ( 40.39 € )
    Raktári cikk - 1 munkanapAznapi kiszállítással elérhető
    46.80 €
    ( 55.69 € )
    Raktári cikk - 1 munkanapAznapi kiszállítással elérhető
    69.69 €
    ( 82.93 € )
    12 munkanapok
    99.18 €
    ( 118.02 € )
    Raktári cikk - 1 munkanapAznapi kiszállítással elérhető
    132.55 €111.34 €
    ( 132.49 € )
    Raktári cikk - 1 munkanapAznapi kiszállítással elérhető
    18.80 €
    ( 22.37 € )
    5 munkanapok
    20.04 €
    ( 23.85 € )
    5 munkanapok
    25.50 €
    ( 30.34 € )
    Raktári cikk - 1 munkanapAznapi kiszállítással elérhető
    27.53 €
    ( 32.76 € )
    11 munkanapok
    44.19 €
    ( 52.59 € )
    11 munkanapok
    60.91 €
    ( 72.48 € )
    15 munkanapok
    90.07 €
    ( 107.18 € )
    5 munkanapok
    105.07 €
    ( 125.03 € )
    17 munkanapok
    166.14 €
    ( 197.71 € )
    5 munkanapok
    16.96 €
    ( 20.18 € )
    5 munkanapok
    17.99 €11.51 €
    ( 13.70 € )
    Raktári cikk - 1 munkanapAznapi kiszállítással elérhető
    22.77 €
    ( 27.10 € )
    Raktári cikk - 1 munkanapAznapi kiszállítással elérhető
    27.55 €
    ( 32.78 € )
    Raktári cikk - 1 munkanapAznapi kiszállítással elérhető
    38.36 €
    ( 45.65 € )
    Raktári cikk - 1 munkanapAznapi kiszállítással elérhető
    48.94 €
    ( 58.24 € )
    11 munkanapok
    91.33 €
    ( 108.68 € )
    5 munkanapok
    116.83 €
    ( 139.03 € )
    12 munkanapok
    156.24 €
    ( 185.93 € )
    12 munkanapok
    22.09 €12.15 €
    ( 14.46 € )
    Raktári cikk - 1 munkanapAznapi kiszállítással elérhető
    21.08 €
    ( 25.09 € )
    12 munkanapok
    29.84 €
    ( 35.51 € )
    Raktári cikk - 1 munkanapAznapi kiszállítással elérhető
    32.27 €
    ( 38.40 € )
    11 munkanapok
    46.35 €
    ( 55.16 € )
    11 munkanapok
    64.21 €
    ( 76.41 € )
    9 munkanapok
    103.62 €
    ( 123.31 € )
    5 munkanapok
    134.71 €109.12 €
    ( 129.85 € )
    Raktári cikk - 1 munkanapAznapi kiszállítással elérhető
    189.94 €
    ( 226.03 € )
    Raktári cikk - 1 munkanapAznapi kiszállítással elérhető

    Részletes információk

    Alapvető információk

    Vázlat és specifikációk

    Back to the Category Linear Ball Bushings

    Technical Drawing - Linear Ball Bushings

     

    Flanged Linear Bushing/Double Bushing/With Lubrication Unit MX:Related Image

     

    Specification Tables - Linear Ball Bushings

     

    Part NumberD ToleranceLL1VHTdd1tP.C.D.WFAEccentricityRows of Balls*
    Perpendicularity
    Basic Load RatingAllowable Static Moment (Mo N • m)Mass (g)
    TypedrTolerance No Surface TreatmentSurface Treatment ToleranceC (Dynamic) NCo (Static) NRound FlangeSquare FlangeCompact Flange
    LHFRW-MX
    LHFSW-MX
    LHFCW-MX
    LHFRWM-MX
    LHFSWM-MX
    LHFCWM-MX
    10 0
    - 0.010
    19 0
    - 0.016
     0
    - 0.021
    6555±0.354064.57.54.12930-290.01540.01558811007.241028294
    122168575.5423232-32657120010.911494106
    16288270648383722311230235019.7197172189
    20 0
    - 0.012
    32 0
    - 0.019
     0
    - 0.025
    948075485.595.1434224360.02050.0201400274026.8271236258
    25401301129625150324061560314043.4559519544
    30451431231074106.6116.1605835492490549082.8704614669
    35 0
    - 0.015
    52 0
    -0.022
     0
    - 0.030
    1571351182676438550.0250.025265062701101048958973
    40601751511296139148.17875456434308040147160314131456
    50802201921411698925680608015900397366334633500
    kgf=Nx0.101972
    For Precautions for Use, see Here. Select Height-adjusting Spacers for Flanged Bushings from Here.
    * Perpendicularity of D to flange mounting surface