Cavity Insert Blocks with Slit Vent (SGWD24)

MISUMI

Product Details:

Manufacturer part number: SGWD24

Brand: MISUMI

Price: 214.46 €

Delivery time: 5 Days

Technical Data:

A (Vertical): 24 mm

B (Horizontal): 10 mm

T (Height): 10 mm

Part Number

Once your search is narrowed to one product,
the corresponding part number is displayed here.

SGWD24

Drawing
3D Preview 3D preview is available after complete configuration
Part Numbers
More Information
Alterations

Drawing / Product specification

*Gas Release Slit Width: 0.012 mm (guideline)

Material SUS304C

Specifications table

t	B	T	Part Number
t	B	T	Type	A
0.5	5.5	5	SGWD	12
1	10	10	SGWD	24

Order

Part Number:

3D preview is not available, because the part number has not yet been determined.

In order to open the 3D preview, the part number must be fixed.

Plug-in is required for 3D Preview

CAD Download

Data to be displayed: 30; 45; 60

Part Number
SGWD24

Part Number	Standard Unit Price	Minimum order quantity	Volume Discount	Standard Shipping Days ?	A (Vertical) (mm)	B (Horizontal) (mm)	T (Height) (mm)
	214.46 €	1		5 Days	24	10	10

Related Information

■ Precautions for Processing
(1)	The four ⒶⒷ sides can be polished. Abrasive residue from polishing entering the vent area may cause blockage
(2)	Wire cutting and electric discharge are the only available processing for the upper and lower surfaces of the slit. This product is made of layered stainless steel material about 0.2 mm thick. Make sure the surface roughness is about 10 μm under the electric conditions for thin plates, since large sparks may be produced and clogging may occur under the conditions for thick plates.
■ How to Mount
(1)	Square up four surfaces Since right angles are not provided on the product sides (Fig. 1 ⒶⒷ surfaces), perform squaring by grinding. We recommend using additional processing KD.
(2)	Processing of upper and lower slit surfaces (as needed) To adjust the shape to match the product part, perform wire cutting or electric discharge on the Fig. 1 upper and lower slit surfaces.
(3)	Assembling into cavity core Assembly methods include 1) press-fitting and 2) flange + spacer. For the flange + spacer method, provide flange processing according to Fig. 2. Milling, wire cutting or grindstone polishing are possible. When specifying additional machining FC, the product will be delivered with flange processing provided to the specified dimensions.

■ Maintenance Method
	When the gas release effect weakens, wash with an organic solvent, etc. In addition, a vacuum generator (M-VCL, M-VCLH) can be used in combination to support the gas release.
■ Features

This part is used for gas release, with a fine slit structure made possible by diffusion
bonding technology.
It is installed to release gas and residual air from the slit part (approx. 0.012 mm).
With multiple slits, it demonstrates high gas releasing performance.

Cavity Insert Blocks with Slit Vent

	Vent is wide enough to handle final filling part misalignment as well
	Since slits are arranged on the entire product part contact surface, it can also handle deviation of the final filling position due to minute fluctuations in molding conditions and differences in the resin lot. This greatly increases the efficiency of positioning during designing and condition setting during molding.


	Linear passage makes resin clogging unlikely
	Since the gas passage is linear, clogging of resin due to solidification of gas in the middle of the passage is reduced. This reduces downtime due to maintenance and contributes to the efficiency of the molding cycle.

	Equivalent or higher gas release effect at low cost
	The installation costs are lower compared to other methods when releasing gas from the same area, and since the aperture ratio (※) is high, it exhibits high gas releasing performance.

Cavity Insert Blocks with Slit Vent

Alterations

This page is Cavity Insert Blocks with Slit Vent, part number SGWD24.
You can find the detail information about specifications and dimensions on part number SGWD24.

Configure

1Suggestion of an applicable part number.

View Part Numbers

Some specification is not specified yet.

The part number is completed.

Basic Attributes